#hazzy | Logs for 2019-03-21
Back
[00:16:34] <hazzy-m> no, the settings are for things the user needs to be able to change on the fly, jog speed, jog inc etc.
[00:45:35] -!- logs has joined #hazzy
[00:45:35] -!- mode/#hazzy [+o logs] by ChanServ
[00:45:36] <Lcvette> Gotcha
[00:48:41] <Lcvette> For your springs, you have a pressure gauge for testing them?
[00:49:07] <Lcvette> On the corvair
[00:50:16] <hazzy-m> No, but I borrowed one
[00:51:06] <Lcvette> Check them at install height and compressed height for the total lift
[00:58:53] <hazzy-m> I did, the machine had stops for each length and ranges marked on the dial for acceptable values
[01:00:10] * hazzy-m stokes the fire
[01:00:33] <Lcvette> Was it specific for corvair springs?
[01:01:01] <Lcvette> Valve springs can have a wide range of pressures
[01:01:10] <hazzy-m> Yes, it was original GM service machine
[01:01:17] <Lcvette> Ok
[01:01:31] <Lcvette> Good deal
[01:02:07] <Lcvette> I bet they are baby pressures
[01:02:14] <hazzy-m> he had another one for testing springs for racing heads
[01:02:23] <hazzy-m> Yeah they are lol
[01:02:28] <Lcvette> Lol
[01:04:31] * hazzy-m uploaded an image: IMG_20190321_010410709.jpg (105KB) < https://matrix.org >
[01:05:16] <Lcvette> Omg
[01:05:19] <Lcvette> Lol
[01:05:25] <hazzy-m> I have the super turbohair lol
[01:05:49] <Lcvette> Lol
[01:06:07] <hazzy-m> What do modern springs run?
[01:08:36] <Lcvette> I run solid roller lifters in my vette with .710" lift, closed pressure is 270lbs, open is 625lbs
[01:09:02] <Lcvette> Max room is 8200rpm
[01:09:08] <hazzy-m> Wow! That is a little more
[01:09:14] <Lcvette> 355ci sbc LT4
[01:09:23] <hazzy-m> Nice!
[01:09:48] <Lcvette> Need allot of spring pressure, run 42psi boost
[01:10:03] <Lcvette> On the back of a 2.08" valve
[01:10:22] <Lcvette> So you loose some of that pressure rating
[01:10:44] <hazzy-m> I was about to ask why you need that, since the cylinder pressure keeps them closed, but I forgot about boost
[01:11:05] <hazzy-m> That is a BIG valve
[01:11:15] <hazzy-m> 4 valves?
[01:11:43] <Lcvette> 2
[01:12:13] <hazzy-m> Ok
[01:12:24] <Lcvette> 142lbs on the back of the v valve from boost
[01:12:56] <hazzy-m> Somebody offered me some big valve heads on insta lol
[01:12:56] <Lcvette> Adds up
[01:13:24] <Lcvette> Also need allot of spring for rpm
[01:13:46] <hazzy-m> Yeah, I guess you also need to make sure the valve closes quickly at those RPMs
[01:13:52] <hazzy-m> Lol
[01:14:23] <Lcvette> Higher the revs, the higher the inertial mass of the valve
[01:15:05] <Lcvette> Not enough spring and the valves float
[01:15:49] <hazzy-m> Right, I think the max stock rated speed on this engine is about 6000 rpm, 8300rpm is really up there
[01:16:10] <hazzy-m> 8200
[01:16:18] <Lcvette> Then you need big pushrods made of light high strength steel
[01:16:50] <Lcvette> Or else they flex under the spring pressures
[01:17:23] <hazzy-m> I guess that is the advantage of an overhead cam
[01:17:32] <Lcvette> Yes
[01:18:03] <Lcvette> And usually no lifter
[01:18:11] <Lcvette> So a lighter spring can be used
[01:18:56] <Lcvette> And usually 4 valve heads so more curtain area with much less mass moving
[01:19:15] <Lcvette> Why fohc engines are usually better for revs
[01:19:22] <Lcvette> Dohc*
[01:20:05] <Lcvette> We have a LT5 Corvette
[01:20:28] <Lcvette> Gosh, that's from before you were born
[01:20:29] <Lcvette> Lol
[01:20:47] <Lcvette> The ZR1
[01:21:33] <Lcvette> They had all aluminum DOHC 4 valve motors
[01:22:10] <Lcvette> 1994 model year
[01:22:27] <Lcvette> 405hp from the factory
[01:23:27] <Lcvette> We have modded it over the years and it's now dining set 568rwhp naturally aspirated
[01:23:42] <Lcvette> Dynoing
[01:23:46] <hazzy-m> Nice!!!
[01:24:11] <hazzy-m> Now give it some boost!
[01:24:18] <Lcvette> It sound 7500rpm and is smooth as silk through the power band
[01:24:39] <Lcvette> We considered it, but there's just not allot of room
[01:26:14] <hazzy-m> Ah, and it's not like it's lacking power lol
[01:26:44] * Lcvette uploaded an image: _20190321_012612.JPG (204KB) < https://matrix.org >
[01:27:26] <Lcvette> Yeah it's already a beast like it is
[01:27:38] <Lcvette> And is dead reliable
[01:27:41] <hazzy-m> That's a beautiful engine compartment!
[01:28:36] * hazzy-m doses off
[01:29:06] <Lcvette> GM had the engines built by lotus
[01:29:13] <Lcvette> Ok, get some rest
[01:29:35] <hazzy-m> Night!
[05:52:27] <JT[m]1> morning
[05:58:07] <silopolis[m]> morning
[05:58:30] <jthornton> morning
[07:43:56] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 06-39-49.png (56KB) < https://matrix.org >
[07:43:58] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 06-40-30.png (57KB) < https://matrix.org >
[07:44:16] <JT[m]1> smart MDI entry
[08:07:19] <Lcvette> morning
[08:07:53] <Lcvette> I like it JT
[08:26:04] <JT[m]1> you press say G then 2 then load parameters it's cool
[08:26:32] <JT[m]1> just need to make a popup help window for the g code with the syntax and description
[08:29:35] <Lcvette> nice!!
[08:40:17] -!- pcw_home has quit [Quit: Leaving]
[08:49:39] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 07-49-09.png (58KB) < https://matrix.org >
[08:49:56] <JT[m]1> I added the description of the G code
[08:50:12] <Lcvette> what happened to the rest of the buttons?
[08:50:50] <Lcvette> or is that how it works?
[08:51:06] <Lcvette> when you hit the first button only relative buttons are displayed after that?
[08:52:29] <JT[m]1> no, the buttons are populated with the words for that G code only sec I
[08:52:35] <JT[m]1> 'll show you
[08:52:55] <Lcvette> \o/
[08:52:59] <Lcvette> :d
[08:53:15] <Lcvette> :D
[08:55:56] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 07-55-26.png (61KB) < https://matrix.org >
[08:58:05] <Lcvette> i see the g code definition
[08:58:19] <Lcvette> im still fuzzy on what you are doing
[08:58:27] <Lcvette> :(
[08:58:43] <Lcvette> is it just a helper aid?
[09:00:10] <silopolis[m]> and only compatible addresses stay active on keypad
[09:00:45] <JT[m]1> it's a MDI entry and rather than having every possible button I only show words that are relevant to that G code
[09:00:52] <silopolis[m]> some kind of interactive keyboard... like it !
[09:01:16] <Lcvette> ok
[09:01:20] <Lcvette> so i was right
[09:01:21] <Lcvette> :D
[09:01:24] <Lcvette> makes sense
[09:01:27] <Lcvette> good thinking!
[09:01:31] <Lcvette> make it a widget?
[09:01:33] <JT[m]1> even G codes that don't have any words the description shows up for your reference I'll show you
[09:02:08] <Lcvette> make it into part of the virtual keyboard widget
[09:02:20] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 08-01-53.png (58KB) < https://matrix.org >
[09:02:21] <Lcvette> for QtPyVCP
[09:02:59] <silopolis[m]> just a little uncertain/uncomfortable with the three words above num keypad 🤔
[09:03:32] <Lcvette> IJK?
[09:03:38] <silopolis[m]> yes
[09:03:43] <Lcvette> they are for arcs
[09:03:50] <JT[m]1> what do you mean?
[09:06:30] <silopolis[m]> I know, I mean being used to "isolated" num keypad, it feels "strange" to have words above it. I'd better had a "words pad" on the left and a "num pad" on the right, and maybe use the thre remaining keys for other functions, with color coding for example
[09:06:42] <Lcvette> do a quick youtube on gcode I J K it will pop up several great tutrial vids on how to calculate those values if you want to do them manually
[09:07:14] <JT[m]1> I understand what you mean sec
[09:07:59] <silopolis[m]> for ex move bksp/suppr there ?
[09:10:26] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 08-10-05.png (63KB) < https://matrix.org >
[09:10:45] <JT[m]1> hmm my frame border did not show up lol
[09:11:15] <Lcvette> lcvette liked the previous layout better
[09:12:01] <silopolis[m]> Great ! Much better IMHO 👍
[09:12:09] <silopolis[m]> lol
[09:13:02] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 08-12-39.png (61KB) < https://matrix.org >
[09:13:59] <silopolis[m]> niiiiice :)
[09:15:50] <silopolis[m]> Aren't bck/fwd arrows missing ? may be begin/end of line also ? and a suppr while there ?! 😁
[09:16:40] <JT[m]1> just has a backspace key
[09:16:56] <JT[m]1> supper?
[09:17:30] <silopolis[m]> sorry "del" (ah those frenchies ;P )
[09:19:06] <roguish[m]> JT: geeze JT, it's getting fancier....
[09:20:05] <silopolis[m]> JT: so you can't navigate left and right in the line ?
[09:20:39] <JT[m]1> not yet no
[09:20:49] <JT[m]1> one thing at a time lol
[09:21:50] <silopolis[m]> oh ok, fine, no pressure... just do it next ! :D
[09:25:18] <JT[m]1> roguish: I'm hoping it's getting easier to use... just thinking I can show what each word means maybe if I don't run out of room
[09:26:03] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 08-25-41.png (60KB) < https://matrix.org >
[09:26:11] <roguish[m]> is it stable enought to run a mill?
[09:26:44] <JT[m]1> yea, I just need to push it and make the 'Send' key work
[09:26:55] <Lcvette> JT, you can use word wrap
[09:27:07] <roguish[m]> is it easy to keep updated after install?
[09:27:15] <Lcvette> just make the label tall enough for it
[09:27:38] <roguish[m]> Lcvette: sheeze, you're becoming quite the programmer....
[09:27:40] -!- pcw_home has joined #hazzy
[09:27:54] <Lcvette> only on the graphical portion
[09:28:05] <Lcvette> lol
[09:28:55] <Lcvette> JT, just check the box in the designer for word wrap and it will wrap test longer than the box length automagically
[09:28:57] <Lcvette> :D
[09:39:10] <JT[m]1> roguish: yea you just have to do a git pull in the cloned directory
[09:39:30] <JT[m]1> geez I need to hit the shower and start my day
[10:39:50] * silopolis[m] thinks it such a pain sometimes to tchat with those chinese sales 😫
[10:53:36] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 09-53-10.png (67KB) < https://matrix.org >
[10:53:52] * JT[m]1 is done cleaning up chicken poop and heads to the shop
[10:56:39] <hazzy-m> JT looks great!
[11:06:48] <roguish[m]> hazzy: hazzy, just installed JT's mill_touch, and get an error 'can't execute DISPLAY program pyvcp'
[11:07:06] <Lcvette> :O
[11:07:09] <roguish[m]> do I still need that environment line?
[11:09:34] <roguish[m]> that 'export PATH=$PATH:~/.local/bin/ ????
[11:10:34] <JT-Shop> either that or copy .xsessionrc to your home folder
[11:10:45] <JT-Shop> buildbot is down for the count it seems
[11:10:54] <roguish[m]> answered my own question. YES still needed.
[11:11:47] <JT-Shop> once seb comes back to life and fixes the buildbot and your up to date you won't need that but until then...
[11:18:58] <hazzy-m> JT-Shop: I hate to bug seb, but he does not seem to have been reading the IRC logs for some time, should I email him or just let it float?
[11:24:33] <JT-Shop> try sending an email to him, I mentioned his name on dev but no response
[11:25:47] <roguish[m]> SUCCESS. got it going. had to set the path thing in a terminal and run from there. also had to strip my pyvcp side panel stuff from the .ini,
[11:29:16] <JT-Shop> roguish[m]: the stuff I did this morning is not on the repo yet but will be soon
[11:30:53] <roguish[m]> ok, just setting up. that's why i asked about updating... no problem. gotta run parts today. rewire some motor leads, move touch screen to the mill, etc, etc, etc,......
[11:31:03] <roguish[m]> no chickens though.
[11:31:58] <roguish[m]> sitting in my office running the mill machine using MobaXterm.
[11:32:30] <roguish[m]> wouldn't do it for reals, just for quick editting and stuff.
[12:10:46] * JT[m]1 is on a lunch minute so pushed to mill_touch
[13:06:44] <JT[m]1> roguish: https://jethornton.github.io
[13:07:22] <JT[m]1> might take a few minutes for the last push to show up in the docs
[14:53:29] <JT-Shop> dropped off a part at a local factory and the owner sent me home with two machines to quote!
[15:21:16] <hazzy-m> JT-Shop: Nice!
[15:24:35] * TurBoss sent a long message: < https://matrix.org >
[15:26:29] <hazzy-m> who, nice!!
[15:26:42] <hazzy-m> we can make our own installer
[15:27:12] <TurBoss> I'm writing a mini python script to get webhooks from github and build the pip packages
[15:27:43] <hazzy-m> what webhook should I add?
[15:28:12] <TurBoss> I'll send you
[15:28:25] <TurBoss> but not ready yet
[15:30:21] <hazzy-m> ok
[15:42:46] <Lcvette> going to Python 3.5.3?
[15:42:51] <Lcvette> :O
[15:43:03] <Lcvette> thought we were stuck using Python 2.7
[16:44:39] <JT-Shop2> hazzy-m: that finger joint jig I showed you the other day works perfect, I can dial in the finger width to within 0.001"
[16:50:18] <hazzy-m> JT-Shop2: Nice!
[17:52:35] <hazzy-m> Hurray!!! Seb is on the buildbot
[17:58:19] <Lcvette> \o/ Hurray!
[18:04:23] <Lcvette> hazzy, did that thing turboss posted mean we are upgrading to a later python?
[18:04:41] <hazzy-m> no
[18:04:57] <hazzy-m> he is just working on the pip server
[18:05:07] <Lcvette> oh
[18:05:54] <Lcvette> Seb is fixing travis?
[18:06:27] <Lcvette> or is travis different than buildbot?
[18:06:46] * JT[m]1 uploaded an image: VectorImage_2019-03-21_050633.jpg (275KB) < https://matrix.org >
[18:07:36] <Lcvette> 🐔🐔🐔
[18:08:19] <Lcvette> 🐓🐔
[18:08:38] <Lcvette> chkinz
[18:08:54] <JT[m]1> LOL
[18:12:23] <JT[m]1> Hazzy did you email seb?
[18:14:46] <hazzy-m> yes, and he wrote right back saying he was on it!
[18:15:02] <hazzy-m> he said it is suposed to email him if it hangs, but it didn't lol
[18:15:55] <JT[m]1> Good deal, I think I'll offer to assist with the buildbot and see what he says.
[18:17:07] <JT[m]1> Now that we know we can email him too
[18:18:03] <hazzy-m> Yeah, that is a good idea, as it seems he is trying to spend less time on LCNC. I am willing to help with it too if that is feasable
[18:18:09] <JT[m]1> Are you making any progress with settings?
[18:18:43] <hazzy-m> yes, I think I am going to mege what I have so far, and kinda do it in two stages
[18:18:55] <JT[m]1> Maybe we should both offer to help
[18:18:55] <hazzy-m> I'll try to get that done tonght
[18:19:07] <JT[m]1> Great
[18:20:23] <hazzy-m> I'm not sure what the build system entails as far as hardwear goes, but I assume it is a fair amount
[18:20:54] <JT[m]1> You mentioned something about the class level the other day, did you sort that out?
[18:22:51] <JT[m]1> Yea I think the buildbot is a fast pc with lots of drives IIRC
[18:23:47] <hazzy-m> no, still not sure how best to do that, I think I might try to do the class level settings using a subclass of pyqtProperty so they can have default setting set in designer
[18:24:11] <hazzy-m> but i'm struggling a bit with the QMetaObject stuff
[18:25:53] <JT[m]1> <hazzy-m "but i'm struggling a bit with th"> I've never messed with QMetaObject stuff yet
[18:30:32] <Lcvette> QMetaObject
[18:30:38] <Lcvette> need googlefu assistance?
[18:30:43] <Lcvette> how can I help?
[18:31:39] <Lcvette> https://stuff.mit.edu
[18:36:01] <Lcvette> you need to use the Q_Object Macro HAzzy!
[18:36:06] <Lcvette> :O
[18:36:10] <Lcvette> I solved it!
[18:36:48] <Lcvette> https://stuff.mit.edu
[18:39:54] <hazzy-m> LOL
[18:40:00] <hazzy-m> those MIT docs are good
[18:40:08] <hazzy-m> had not seen them before
[18:43:06] <Lcvette> yeah?
[18:43:07] <Lcvette> i helped some?
[18:43:13] <Lcvette> \o/
[18:43:18] <hazzy-m> yes
[18:43:22] <hazzy-m> o/
[18:43:32] <Lcvette> Nubby4lyfe
[18:43:37] <hazzy-m> LOL
[18:43:39] <Lcvette> :D
[18:43:54] * JT[m]1 can't stop sampling the chicken broth lol
[18:43:54] <hazzy-m> springs some on saturday
[18:44:17] <hazzy-m> JT is making hazzy hungry
[18:44:52] * JT[m]1 is making chicken soup or dumplings not sure at this point
[18:45:09] <Lcvette> 🐔😢
[18:45:17] <JT[m]1> we freeze the broth seperate from the chicken in serving size containers
[18:45:22] <hazzy-m> Hurray! Buildbot is running again
[18:45:33] <Lcvette> \o/
[18:45:36] <hazzy-m> ETA in ~ 212 hrs 14 mins at 12:59 19 pending
[18:45:37] <hazzy-m> LOL
[18:46:03] <jthornton> was 20 pending when we tried to force build today
[18:46:04] <Lcvette> "This is what it looks like..... when chicks cry"
[18:47:02] <Lcvette> that broth is made from chicken tears Jthornton
[18:47:12] <Lcvette> :(
[18:47:24] <JT[m]1> looks like the debs are all building for the most part
[18:48:09] <Lcvette> 212hrs?
[18:48:11] <Lcvette> :O
[18:48:47] <Lcvette> JT: how about chicken and pastry?
[18:50:18] <JT[m]1> I either make chicken soup with some Wondra to thicken the broth or dumplins by adding some flour taco bits
[18:50:35] <JT[m]1> we don't eat sweet stuff or much bread
[18:50:44] <Lcvette> lol
[18:50:53] <Lcvette> chicken and pastry isn't sweet
[18:51:17] <Lcvette> its like the southern country version of chicken and dumblins
[18:51:21] <JT[m]1> when i think pastry I think about sticky buns lol
[18:51:27] <Lcvette> hahaha
[18:51:34] <Lcvette> yeah that doesn't sound too enticing
[18:51:55] <Lcvette> try a chicken pastry recipe, bet you' add it to your repitoir
[18:52:00] <Lcvette> sp?
[18:52:07] <JT[m]1> you got one?
[18:53:18] <Lcvette> this is the one we use
[18:53:22] <Lcvette> http://www.tasteofsouthern.com
[18:53:48] <Lcvette> its soooo goood
[18:54:00] <Lcvette> one of my favorite meals
[18:55:45] <JT[m]1> yea that's how I used to make chicken and dumplins
[18:56:04] <JT[m]1> except I use a pizza cutter it's way faster
[18:56:42] <Lcvette> yeah we do too
[18:56:44] <Lcvette> lol
[19:00:32] <JT[m]1> I'm really liking the idea of having the G code info right at my finger tips in the MDI window
[19:00:58] <Lcvette> yeah, thats pretty sweet!
[19:13:25] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 18-12-59.png (63KB) < https://matrix.org >
[19:13:27] * JT[m]1 uploaded an image: Screenshot at 2019-03-21 18-12-34.png (246KB) < https://matrix.org >
[19:13:46] <JT[m]1> Lcvette: the screen changes from qt designer, any clue why?
[19:14:14] <Lcvette> train my eye to the spot you refer
[19:14:21] <JT[m]1> see how the bottom two rows are wider when ran
[19:14:54] <Lcvette> yes
[19:14:54] <JT[m]1> in the MDI tab
[19:15:06] <Lcvette> ok
[19:15:24] <Lcvette> so you have a box definition defined differently
[19:15:27] <JT[m]1> also the mdientry and label are not the same width
[19:15:54] <JT[m]1> you want to look at it?
[19:16:10] <Lcvette> yeah
[19:16:16] <Lcvette> how do i get to your gui
[19:16:27] <Lcvette> and access in designer?
[19:16:51] <JT[m]1> sec
[19:17:04] <Lcvette> k
[19:17:19] <JT[m]1> https://github.com
[19:17:21] <JT[m]1> and
[19:17:36] <JT[m]1> https://jethornton.github.io
[19:18:19] <JT[m]1> do the install and be able to edit
[19:18:21] <Lcvette> what do i do?
[19:18:35] <JT[m]1> git clone https://github.com
[19:18:48] <JT[m]1> cd mill_touch
[19:18:52] <JT[m]1> pip install -e .
[19:19:07] <Lcvette> ok i see follo install instructions
[19:19:08] <Lcvette> lol
[19:19:28] <JT[m]1> aye
[19:21:08] <Lcvette> ah, ok
[19:21:11] <Lcvette> so
[19:21:28] <Lcvette> rememeber when i said you should use widgets to group buttons
[19:21:33] <Lcvette> this is why
[19:22:01] <JT[m]1> ah ok
[19:22:26] <JT[m]1> were you able to open it in qt designer?
[19:22:37] <Lcvette> but you also have the main box set as prefered
[19:22:53] <Lcvette> which means the buttons can dictate its size
[19:23:16] <JT[m]1> ah didn't know that
[19:23:47] * Lcvette uploaded an image: image.png (19KB) < https://matrix.org >
[19:23:58] <Lcvette> see the grayed out width and height
[19:24:10] <Lcvette> change preferred to fixed
[19:24:25] <JT[m]1> yep I see it
[19:24:25] <Lcvette> then add those numbers in the max width and height boxes below it
[19:24:31] <Lcvette> should contrain the box size
[19:24:43] <JT[m]1> in the gridFrame?
[19:24:45] <Lcvette> then your layout margins will be effective
[19:25:20] * Lcvette uploaded an image: image.png (24KB) < https://matrix.org >
[19:26:06] <Lcvette> gridframe
[19:26:07] <Lcvette> yes
[19:26:52] <Lcvette> those springs
[19:26:58] <Lcvette> are not your friend
[19:27:01] <Lcvette> lol
[19:27:07] <Lcvette> i WOULD NOT USE THEM
[19:29:22] <JT[m]1> if you copy the config to your linuxcnc configs directory you can run it and putz with it, I still can't get it to align
[19:30:08] <Lcvette> yeah you have alot of things under tension
[19:30:42] <Lcvette> i find you have best results when you use limited expanding widgets
[19:31:00] <Lcvette> and have some that are fixed to help define your layout better
[19:31:13] <Lcvette> that way things don't unspring when you make a change
[19:31:39] <Lcvette> better to have one expanding item if you know the screen is a fixed resolution
[19:32:35] <Lcvette> or if you want the screen to expand as a whole then you will want to constrain each set of buttons so they grow uniformly
[19:37:34] <JT[m]1> if you want to putz with it I'll give you push access to the repo
[19:38:07] <Lcvette> im putzing now
[19:38:07] <Lcvette> :D
[19:38:28] <Lcvette> lets do that in the morning
[19:38:35] <Lcvette> im gonna try and fix this right now though
[19:38:43] <Lcvette> before tv time with the wife
[19:40:19] <JT[m]1> ok
[19:41:40] <Lcvette> gridframe
[19:41:41] <Lcvette> blah
[19:43:10] <JT[m]1> do whatever you want to the layout and style, you can push from gitkracken now
[19:43:21] <Lcvette> ok nice!
[19:43:46] <JT[m]1> oh you have to accept the invite
[19:44:00] <JT[m]1> https://github.com
[19:46:26] <JT[m]1> I'll keep working on the MDI help text and stuff like that
[20:06:15] <hazzy-m> hurray! got a LCNC update
[20:14:26] <Lcvette> \o/ Hurray!
[20:20:34] -!- biqut2 has joined #hazzy
[20:22:23] <Lcvette> JT: i can't open the actual gui
[20:22:56] * Lcvette sent a long message: < https://matrix.org >
[20:23:39] * Lcvette sent a long message: < https://matrix.org >
[20:24:04] <Lcvette> first one is the white error message, second one is the terminal box from the failed start attempt
[20:24:07] <Lcvette> hazzy?
[20:31:30] <hazzy-m> Lcvette: checking
[20:39:38] <hazzy-m> hmm, mill_touch runs fine here
[20:43:44] <Lcvette> I dunno
[20:44:18] * hazzy-m starts a fire
[20:44:22] <Lcvette> Maybe I installed it wrong
[20:44:51] <Lcvette> I did it in the main terminal
[20:44:59] <Lcvette> Opened in designer
[20:45:34] <Lcvette> But it's not in qtpyvcp folder
[20:45:41] <Lcvette> Is that it?
[20:54:37] <JT[m]1> no, it will be in a directory by itself
[20:55:15] * JT[m]1 just popped down to lock up the chickens
[20:55:33] <Lcvette> Ok
[20:55:43] <Lcvette> Then it should be installed right I guess
[20:56:15] <Lcvette> Not sure why it won't open
[20:58:12] <Lcvette> It's all fixed I think just need to verify
[21:08:19] <hazzy-m> does it work now?
[21:09:18] <Lcvette> No
[21:09:51] <Lcvette> I was referring to the fix I did in designer for it for jt
[21:10:12] <Not-e6c6> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03master [+0/-0/±1] 13https://git.io/fjfpo
[21:10:14] <Not-e6c6> [02qtpyvcp] 07KurtJacobson 03a4c4c74 - BUG: fix "No JSON object could be decoded" error
[21:10:14] <hazzy-m> ah
[21:10:22] <Lcvette> But I can't open the actual GUI from the launcher
[21:11:01] <hazzy-m> hmm, it is an import error for "widget", don't know where that would be coming from
[21:12:23] <Not-e6c6> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03gh-pages [+442/-0/±0] 13https://git.io/fjfpi
[21:12:24] <Not-e6c6> [02qtpyvcp] 07traviscibot 031bd1607 - Deploy kcjengr/qtpyvcp to github.com/kcjengr/qtpyvcp.git:gh-pages
[21:24:41] <Not-e6c6> [02qtpyvcp] 07KurtJacobson pushed 039 commits to 03master [+6/-0/±32] 13https://git.io/fjfpd
[21:24:43] <Not-e6c6> [02qtpyvcp] 07KurtJacobson 03e78561a - replace debug prints with log messages
[21:24:44] <Not-e6c6> [02qtpyvcp] 07KurtJacobson 03792a9a4 - use jog rate settings slider in ProbeBasic
[21:24:46] <Not-e6c6> [02qtpyvcp] 07KurtJacobson 03c438261 - Merge branch 'Settings'
[21:27:04] <Not-e6c6> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03gh-pages [+442/-0/±0] 13https://git.io/fjfpA
[21:27:05] <Not-e6c6> [02qtpyvcp] 07traviscibot 03cdd0d00 - Deploy kcjengr/qtpyvcp to github.com/kcjengr/qtpyvcp.git:gh-pages
[21:27:27] <hazzy-m> the deed it done, settings is merged
[21:27:48] <hazzy-m> Lcvette Hurray!
[21:54:05] <Lcvette> \o/ Hurray!!!
[21:54:17] <Lcvette> You did it!!
[21:55:43] <Lcvette> Lcvette don't know what to do with them
[21:55:50] <Lcvette> :(
[21:55:54] <Lcvette> Lol
[23:07:38] <hazzy-m> I already added them to PB
[23:09:25] <Lcvette> \o/
[23:10:56] <Lcvette> Oh do I have to log out and in for mill touch?
[23:11:57] -!- biqut2 has quit [Remote host closed the connection]
[23:12:58] -!- biqut2 has joined #hazzy
[23:15:33] <Lcvette> will milltouch be inside the qtpyvcp folder?
[23:15:38] <Lcvette> or should it?
[23:26:01] <Lcvette> i give up on mill touch
[23:26:09] <Lcvette> its busted
[23:34:26] <Lcvette> you here hazzy?
[23:48:34] <hazzy-m> No, mill_touch will be installed in your ~/.local/lib/python2.7 dir
[23:48:43] <hazzy-m> does it not show up in the VCP chooser?
[23:48:53] <hazzy-m> how did you install it?
[23:49:12] <Lcvette> per the instructions
[23:49:16] <Lcvette> was easy
[23:49:23] <Lcvette> it does show up in the chooser
[23:49:26] <hazzy-m> no you done have to log out and back in for mill_touch
[23:49:33] <hazzy-m> hmmm
[23:49:35] <Lcvette> i tried that didn't work
[23:49:59] <Lcvette> i can even push to jt's gitkraken
[23:50:04] <Lcvette> open in designer
[23:50:08] * hazzy-m is enjoying the PB window icon :)
[23:50:12] <Lcvette> but can't open the gui
[23:50:20] <Lcvette> what?
[23:50:25] <Lcvette> oh
[23:50:28] <hazzy-m> very strange
[23:50:45] <hazzy-m> what version of QtPyVCP are you running?
[23:50:56] <hazzy-m> `qtpyvcp -v`
[23:51:25] * Lcvette uploaded an image: image.png (88KB) < https://matrix.org >
[23:51:46] <Lcvette> QtPyVCP v0.2.1+33.gc438261
[23:52:19] <Lcvette> i did the latest updates and upgrades in terminal still no bueno
[23:52:55] <Lcvette> could it be an xsessions thing?
[23:54:23] <Lcvette> wow, thats wierd, it just opened