#hazzy | Logs for 2019-09-20

Back
[00:59:17] -!- c-log has quit [Ping timeout: 276 seconds]
[01:02:08] -!- c-log has joined #hazzy
[01:44:47] -!- c-log has quit [Ping timeout: 265 seconds]
[01:46:24] -!- c-log has joined #hazzy
[01:50:51] -!- KimK has quit [Ping timeout: 250 seconds]
[02:42:01] -!- KimK has joined #hazzy
[02:52:57] -!- c-log has quit [Ping timeout: 245 seconds]
[02:55:53] -!- c-log has joined #hazzy
[05:52:49] <jthornton> log
[05:52:50] <c-log> jthornton: Nothing has been logged today, #hazzy index http://tom-itx.no-ip.biz:81
[06:19:46] <hazzy-m> Morning
[06:20:13] <jthornton> morning
[08:58:46] <Lcvette> morning
[10:13:28] <Tom_L> morning
[11:48:04] <Lcvette> Tom_L: movement!!
[11:48:10] <Lcvette> scale is off
[11:48:13] <Lcvette> need to fix that
[11:51:54] <Lcvette> scale fixed
[11:52:58] <jthornton> fix my faucet lol
[11:53:01] * Lcvette sent a long message: < https://matrix.org >
[11:53:04] <Lcvette> this nwas the fix
[11:53:08] <Lcvette> \o/
[11:58:57] <jthornton> lunch minute is over back to work
[12:01:47] <Lcvette> jogging is smooth as silk too
[12:02:02] <Lcvette> jthornton: i'd rather fix faucets then hal errors
[12:02:03] <Lcvette> lol
[12:59:07] <Lcvette> turboss ru you around?
[13:01:22] <TurBoss> yo
[13:06:14] <Lcvette> did you find the wheel graphic?
[13:12:50] <TurBoss> just restored my computer
[13:13:00] <Lcvette> \o/
[13:13:04] <Lcvette> your up and running now?
[13:13:31] <TurBoss> only have to plug the linuxcnc sdd
[13:13:32] <TurBoss> just checking
[13:13:32] <TurBoss> stuff
[13:13:46] * TurBoss uploaded an image: image.png (1703KB) < https://matrix.org >
[13:13:54] <Lcvette> whoa
[13:13:54] * TurBoss uploaded an image: image.png (1359KB) < https://matrix.org >
[13:14:11] <Lcvette> thats fancy
[13:14:19] <TurBoss> it has a connectr to plug led strips
[13:14:35] <TurBoss> so cpu fan is in sync with color
[13:15:29] <Lcvette> nice
[13:15:48] <TurBoss> give me 10 min
[13:17:30] <Lcvette> is where the images for the qml are located /home/chris/dev/qtpyvcp/qtpyvcp/widgets/display_widgets/atc_widget/images/
[13:25:47] <Tom_L> so how did you figure all that out?
[13:26:12] <Lcvette> Tom_L: dgarret on the forum in the hal section nailed it first try
[13:26:30] <Lcvette> said i needed those lines, i pu them in and voila pendant works!
[13:26:40] <Lcvette> its fantastic, no lag
[13:26:54] <Lcvette> clicks are exact
[13:27:05] <Lcvette> had to move the scale decimal
[13:27:12] <Tom_L> probably has something to do with the joint / axis change. i didn't have to do any of that
[13:27:18] <Lcvette> had it at .0001 .001 .01
[13:27:28] <Tom_L> i wondered if the scale would be off
[13:27:35] <Lcvette> wound up needing .000001 .00001 .0001
[13:27:49] <Lcvette> noty sure maybe something with the ilowpass settings?
[13:28:26] <Tom_L> change it there and see
[13:28:47] <Lcvette> do i need too?
[13:28:57] <Tom_L> that's up to you
[13:29:04] <Lcvette> it seems perfect right now
[13:29:09] <Lcvette> lol
[13:29:20] <Lcvette> im in the middle of replacing the Y axis cars finally
[13:29:22] <Tom_L> i would try it to learn something not necessarily to be changing it
[13:29:36] <Lcvette> ok i will star it for later
[13:29:42] <Tom_L> sometimes i break things to see how they work
[13:29:52] <Lcvette> have a bunch left to do i wanna get done so i can start testing the machine itself
[13:30:41] <Tom_L> so you're using the qt interface too right?
[13:31:11] <Tom_L> for me to try that i'd need a faster pc on the mill
[13:36:17] <Tom_L> looking at your config i'm wondering if and why you need to use joint.0.jog-enable at all if it winds up going to axis.x.jog-enable anyway
[13:36:24] <Tom_L> seems a little redundant to me
[13:36:53] <Lcvette> yeah using the qtpyvcp probe basic interface i designed
[13:37:02] <Tom_L> if it were me, i would test that to find out
[13:37:06] <Lcvette> i have a fast pc with great latency
[13:37:27] <Lcvette> i dunno
[13:37:31] <Lcvette> it works right now
[13:37:38] <Lcvette> take the win!!
[13:37:42] <Lcvette> lol
[13:37:54] <Lcvette> i will test it out once she is all fixed up and running
[13:38:03] <Lcvette> still need to do the probing routine testing
[13:38:06] <Tom_L> send the 7i77 input20 straight to axis.x.jog-enable and bypass the joint.0.jog-enable
[13:38:11] <Lcvette> atc functionality testing
[13:39:10] <Tom_L> if both are needed for some new code they have planned maybe they should be tied internally
[13:39:56] <Tom_L> just me thinking out loud...
[13:40:10] <Lcvette> dgarrett said to add those lines not replace anything else
[13:40:23] <Tom_L> i believe you
[13:40:23] <Lcvette> so im not sure but it seems it probably needs both
[13:40:29] <Lcvette> something about homing
[13:40:35] <Lcvette> but it was over my heaad
[13:40:56] <Lcvette> at the moment, im replacing the bearing cars for the second time.. i would rather not break them a third time
[13:40:57] <Lcvette> lol
[13:41:08] <Tom_L> to make lcnc more generic they went to joint over axis
[13:41:35] <Tom_L> well stop hitting them
[13:42:01] <Tom_L> maybe you should order a box full
[13:43:33] <Lcvette> $$$$$$
[13:43:38] <Lcvette> lol
[13:43:51] <Tom_L> glad you got it going
[13:43:53] <Lcvette> from what i read the joint thing was a benefit
[13:43:57] <Lcvette> did i read it wrong?
[13:44:10] <Lcvette> especially with arc blending
[13:44:13] <Lcvette> look ahead etc
[13:44:19] <Tom_L> maybe, everyone has an opinion
[13:44:34] <Lcvette> smoother movements
[13:44:39] <Lcvette> better acceleration calcs
[13:48:07] <Tom_L> what was the cost of the pendant with the extra buttons you mentioned?
[13:48:18] <Tom_L> link..
[14:01:17] <Lcvette> i don't remember that one
[14:01:59] <Tom_L> got a link to yours again?
[14:02:52] <Tom_L> do they say the radio range on them?
[14:02:57] <Lcvette> the one i bought was just under $200 then with shipping it was just a touch over
[14:03:32] <Lcvette> www.cdxhctech.com
[14:04:02] <Lcvette> http://www.cdxhctech.com
[14:04:36] <Lcvette> http://www.cdxhctech.com
[14:04:41] <Lcvette> thats one with lots of buttons
[14:04:49] <Lcvette> they are radio wireless, not usb
[14:04:57] <Tom_L> right
[14:05:10] <Tom_L> i saw the radio module on the board
[14:05:57] <Tom_L> wonder what the battery life is
[14:06:04] <Lcvette> if you are electronics savvy, you maybe could build one
[14:06:04] <Lcvette> but for me it would wind up a project that never got finished
[14:06:08] <Lcvette> the pendant itself feels very high quality
[14:06:16] <Lcvette> has a great fitted removable rubber skin
[14:06:28] <Lcvette> dunno
[14:06:52] <Lcvette> it has internal battery conservation stuff
[14:07:01] <Lcvette> ie shuts down after so long
[14:07:20] <Lcvette> but move the wheel or switch and it is back on
[14:07:23] <Tom_L> so do i
[14:07:29] <Lcvette> takes 2AA batteries
[14:07:46] <Tom_L> probably out of the price range for my little mill
[14:07:55] <Tom_L> i don't really need it anyway. mine works fine
[14:07:58] <Lcvette> also has a magnetic backing so i can stick it on the door or head or table etc
[14:08:30] <Lcvette> ok back to bearing blocks!
[14:09:06] <Tom_L> you should be good at that task
[14:13:15] <TurBoss> Lcvette i get this error:
[14:13:16] <TurBoss> ```
[14:13:17] <TurBoss> ImportError: No module named probe_basic_rc
[14:19:51] <Lcvette> TurBoss: where?
[14:19:59] <TurBoss> https://qtpyvcp.kcjengr.com
[14:20:01] <TurBoss> found it
[14:20:24] <Lcvette> i need to run that?
[14:20:38] <TurBoss> not sure
[14:20:46] <TurBoss> the install process should do
[14:20:50] <Lcvette> oh
[14:20:54] <TurBoss> I'm trying to fix
[14:20:59] <Lcvette> ok
[14:25:42] <TurBoss> aparently is begin done
[14:26:02] <TurBoss> https://github.com
[14:26:10] <TurBoss> any ideas?
[14:26:33] <TurBoss> from qtpyvcp.tools.qcompile import compile
[14:26:34] <TurBoss> compile(['examples/probe_basic',])
[14:26:47] <TurBoss> * ```
[14:26:48] <TurBoss> from qtpyvcp.tools.qcompile import compile
[14:26:48] <TurBoss> compile(['examples/probe_basic',])
[14:27:02] <hazzy-m> Hmm
[14:27:09] <TurBoss> ```
[14:27:10] <TurBoss> File "/home/turboss/.local/lib/python2.7/site-packages/examples/probe_basic/probe_basic.py", line 11, in <module>
[14:27:16] <TurBoss> site-packages
[14:27:21] <hazzy-m> Are the QT dev tools instead? Should be..
[14:27:21] <Lcvette> i just remember that it was in the qml programe
[14:27:35] <TurBoss> installed?
[14:27:39] <Lcvette> not on this machine
[14:27:39] <TurBoss> ah
[14:28:00] <Lcvette> i wanted to make sure everything installed as a user and keep the system light without the extra stuff
[14:28:01] <TurBoss> not at the time of pip
[14:28:11] <TurBoss> I'll reinstall with pip
[14:32:02] <TurBoss> hurray!
[14:32:02] <TurBoss> pip didn't noticed missing devtools
[14:32:02] <Lcvette> works?
[14:32:02] <hazzy-m> I'm about ready to shoot this guy, he sent enough parts to make a couple of each of 15 different truck covers, when I asked him to select a couple products and send me enough to make 15 of each. Now I have a shit ton of parts to program and only tow of each to run, so no test runs
[14:32:02] <Tom_L> you're just that good
[14:32:02] -!- logs has quit [Ping timeout: 240 seconds]
[14:33:13] -!- logs has joined #hazzy
[14:33:13] -!- mode/#hazzy [+o logs] by ChanServ
[14:33:35] <Lcvette> TurBoss: what do i need to do?
[14:33:48] <TurBoss> wait 10 min lol
[14:34:19] <Lcvette> ok
[14:34:21] <Lcvette> \o/
[14:34:36] <TurBoss> should be up in a min
[14:34:38] * Tom_L taps his foot on the floor impatiently
[14:35:03] <Not-5e4d> [02qtpyvcp] 07TurBoss pushed 031 commit to 03master [+0/-0/±1] 13https://git.io/Je3QW
[14:35:04] <Not-5e4d> [02qtpyvcp] 07TurBoss 03cd196b0 - include png files for distribution
[14:35:58] <TurBoss> ```
[14:35:58] <TurBoss> pip install --upgrade git+https://github.com/kcjengr/qtpyvcp
[14:36:12] <TurBoss> should show the graphics
[14:36:56] <TurBoss> @hazzy the lack of qtdevtools didn't make pip to crash
[14:36:57] <Not-5e4d> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03gh-pages [+460/-0/±0] 13https://git.io/Je3Q8
[14:36:58] <Not-5e4d> [02qtpyvcp] 07traviscibot 03c4792df - Deploy kcjengr/qtpyvcp to github.com/kcjengr/qtpyvcp.git:gh-pages
[14:38:59] -!- jthornton has quit [Read error: Connection reset by peer]
[14:38:59] -!- JT-Shop has quit [Read error: Connection reset by peer]
[14:38:59] -!- JT-Shop2 has quit [Read error: Connection reset by peer]
[14:39:28] <Lcvette> TurBoss: run that?
[14:39:46] <TurBoss> with that you can test the latests master
[14:39:59] <Lcvette> ?
[14:40:07] <TurBoss> if works ok hazzy could make a release
[14:40:24] <Lcvette> what do you mean test the latest master?
[14:40:46] <TurBoss> pick the changes i made for the atc pics
[14:40:52] <TurBoss> the missing ones
[14:41:10] <Lcvette> i don't understand
[14:41:43] * TurBoss sent a long message: < https://matrix.org >
[14:41:46] <Lcvette> i have no dev stuff on this machine to pick anything
[14:41:53] <Lcvette> ok
[14:42:24] <TurBoss> but my changes are on master
[14:42:44] <Lcvette> i just ran the upgrade
[14:43:02] <TurBoss> wich one
[14:43:03] <TurBoss> ```
[14:43:03] <TurBoss> pip install --upgrade git+https://github.com/kcjengr/qtpyvcp
[14:43:07] <TurBoss> ^
[14:43:21] <Lcvette> so no fix in the current upgrade?
[14:43:24] <Lcvette> no
[14:43:26] <Lcvette> the othere
[14:43:33] <Lcvette> pip install --upgrade qtpyvcp
[14:43:33] <TurBoss> ok
[14:43:49] <TurBoss> this one doesn't include the fix yet
[14:44:53] <Lcvette> k
[14:45:00] <Lcvette> i will wait for hazzy to release the fix
[14:45:06] * TurBoss sent a long message: < https://matrix.org >
[14:45:16] <TurBoss> * ```
[14:45:17] <TurBoss> pip install --upgrade git+https://github.com/kcjengr/qtpyvcp
[14:45:18] <TurBoss> ```this command means, hey pip don't pic the release pic the master
[14:45:24] * TurBoss sent a long message: < https://matrix.org >
[14:45:43] <Lcvette> sure he will be busy until maybe later toinuightoh so run that one?
[14:45:53] <TurBoss> yes
[14:45:55] <TurBoss> is safe
[14:45:57] -!- jthornton has joined #hazzy
[14:46:00] -!- JT-Shop has joined #hazzy
[14:46:00] -!- JT-Shop2 has joined #hazzy
[14:46:02] <Lcvette> ok
[14:46:35] <TurBoss> maybe an error is shown
[14:46:40] <TurBoss> and doesn't boot
[14:46:52] <TurBoss> Lcvette: please install this first
[14:47:13] <TurBoss> ```
[14:47:14] <TurBoss> sudo apt install qttools5.dev qttools5-dev-tools
[14:47:30] <TurBoss> may be a requirement since now
[14:47:55] <TurBoss> so we can hacompile resources during the install process
[14:48:05] <Lcvette> the image is there now!
[14:48:13] <TurBoss> oh
[14:48:14] <Lcvette> i did not install the gtools
[14:48:16] <TurBoss> hurray!
[14:48:19] <TurBoss> ok
[14:48:23] <Lcvette> \o/
[14:48:23] <Lcvette> hurray!
[14:48:31] <TurBoss> so not required !hurray
[14:48:31] <Lcvette> i need gls?
[14:48:32] <TurBoss> !
[14:48:39] <TurBoss> now need to be relesaed
[14:48:42] <Lcvette> gttools
[14:48:49] <Lcvette> no nneed?
[14:48:51] <TurBoss> and pip install --upgrade qtpyvcp will work
[14:48:53] <TurBoss> no
[14:48:58] <Not-5e4d> [02qtpyvcp] 07KurtJacobson published 03v0.2.5 | - 13https://git.io/Je3Qo
[14:48:59] <TurBoss> no nned
[14:48:59] <Not-5e4d> [02qtpyvcp] 07KurtJacobson created tag 03v0.2.5 - 13https://git.io/fhCou
[14:49:00] <Lcvette> hurray!
[14:49:00] <TurBoss> * no need
[14:49:01] <Not-5e4d> [02qtpyvcp] 07KurtJacobson tagged 03cd196b0 as 03v0.2.5 13https://git.io/Je3QK
[14:49:07] <TurBoss> lol!
[14:49:16] <TurBoss> \o//
[14:49:20] <TurBoss> * \\\o//
[14:49:24] <TurBoss> * \\o//
[14:49:45] <Lcvette> hahaha
[14:49:47] <Lcvette> hurray!!
[14:49:59] <Lcvette> imm replacing the broken beasring blocks
[14:50:09] <TurBoss> broken?
[14:50:21] <TurBoss> bearing?
[14:50:21] <hazzy-m> Should be up soon
[14:50:21] <Lcvette> yes
[14:50:27] <TurBoss> cool
[14:50:30] <TurBoss> thanks!
[14:50:45] * Lcvette uploaded an image: VectorImage_2019-09-20_025036.jpg (103KB) < https://matrix.org >
[14:51:14] <Lcvette> hazzy: \o/
[14:51:46] <Lcvette> ok back in a bit need to concentrate so i don't break something else\
[14:51:47] <Lcvette> lol
[14:55:26] <Not-5e4d> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03gh-pages [+460/-0/±0] 13https://git.io/Je3Qy
[14:55:27] <Not-5e4d> [02qtpyvcp] 07traviscibot 03b9839b7 - Deploy kcjengr/qtpyvcp to github.com/kcjengr/qtpyvcp.git:gh-pages
[14:55:34] <Not-5e4d> [02qtpyvcp] 07TurBoss pushed 031 commit to 03master [+0/-0/±1] 13https://git.io/Je3QS
[14:55:36] <Not-5e4d> [02qtpyvcp] 07TurBoss 034a74388 - qtpyvcp is now on pypi
[14:56:36] -!- travis-ci has joined #hazzy
[14:56:36] <travis-ci> kcjengr/qtpyvcp#1078 (v0.2.5 - cd196b0 : TurBoss): The build passed.
[14:56:36] <travis-ci> Diff view : https://github.com
[14:56:36] <travis-ci> Build details : https://travis-ci.org
[14:56:36] -!- travis-ci has parted #hazzy
[14:56:36] <Tom_L> has probe basic been tested on hardware yet?
[14:56:52] <TurBoss> yes Infinity did
[14:57:05] <Tom_L> how'd it go?
[14:57:37] <Not-5e4d> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03gh-pages [+460/-0/±0] 13https://git.io/Je3QH
[14:57:38] <Not-5e4d> [02qtpyvcp] 07traviscibot 0367f2a3f - Deploy kcjengr/qtpyvcp to github.com/kcjengr/qtpyvcp.git:gh-pages
[14:57:47] -!- JT-Shop2 has quit [Ping timeout: 250 seconds]
[14:57:47] -!- JT-Shop has quit [Ping timeout: 250 seconds]
[14:58:02] -!- jthornton has quit [Ping timeout: 268 seconds]
[14:58:14] <Infinity[m]1> works alright, had some issues with my PP and it does not show Error messages yet
[14:58:37] <TurBoss> ah cool
[14:58:41] <TurBoss> good reminder
[15:00:06] <Lcvette> Infinity: PP?
[15:00:26] <Infinity[m]1> postprocessor
[15:00:52] <Lcvette> with probe basic?
[15:01:10] <Lcvette> post processor problems with probe basic?
[15:01:44] <TurBoss> should be ngc
[15:01:54] <Infinity[m]1> yes but no 😄 general LinuxCNC problems based on a character in acomment that was not escaped correctly
[15:02:24] <Infinity[m]1> but Axis showed an error and hilighted the line, PB did not
[15:02:57] <TurBoss> oh ok
[15:03:41] <Infinity[m]1> I'm not shure what it was, maybe an german Umlaut like äöü in a Tool name ? Can't remember
[15:03:44] <Lcvette> error messeges not working turboss?
[15:03:57] <TurBoss> ya.. they are silenced
[15:04:03] <TurBoss> problems with dbus
[15:04:22] <TurBoss> we are working on a native qt notification system
[15:04:42] <TurBoss> there is a branch
[15:04:48] <TurBoss> should be finished
[15:06:25] <Lcvette> ah
[15:06:55] <Tom_L> any pitfalls like when in one screen accidental access to things you shouldn't have access to?
[15:07:32] <Tom_L> ie: program mode can't allow the spindle to be turned off etc
[15:08:02] <Tom_L> maybe a bad example but it popped into my head
[15:08:42] <Tom_L> i guess what i'm asking is there error checking built into it?
[15:09:45] <Not-5e4d> [02qtpyvcp] 07TurBoss pushed 031 commit to 03master [+0/-0/±1] 13https://git.io/Je37J
[15:09:47] <Not-5e4d> [02qtpyvcp] 07TurBoss 03a990a07 - typo
[15:10:19] <TurBoss> with rules you can implement thoose
[15:11:32] <TurBoss> https://qtpyvcp.kcjengr.com
[15:11:47] <TurBoss> !log
[15:11:47] <c-log> TurBoss: Today's Log http://tom-itx.no-ip.biz:81
[15:12:48] <Not-5e4d> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03gh-pages [+460/-0/±0] 13https://git.io/Je37L
[15:12:50] <Not-5e4d> [02qtpyvcp] 07traviscibot 03f917d99 - Deploy kcjengr/qtpyvcp to github.com/kcjengr/qtpyvcp.git:gh-pages
[15:15:03] <TurBoss> https://qtpyvcp.kcjengr.com
[15:15:16] <TurBoss> oops
[15:15:16] <TurBoss> XD
[15:18:11] -!- jthornton has joined #hazzy
[15:18:13] -!- JT-Shop has joined #hazzy
[15:18:52] <Not-5e4d> [02qtpyvcp] 07TurBoss pushed 031 commit to 03master [+0/-0/±1] 13https://git.io/Je373
[15:18:53] <Not-5e4d> [02qtpyvcp] 07TurBoss 033a82cab - gitter room was moved
[15:20:56] <Not-5e4d> [02qtpyvcp] 07KurtJacobson pushed 031 commit to 03gh-pages [+460/-0/±0] 13https://git.io/Je37G
[15:20:58] <Not-5e4d> [02qtpyvcp] 07traviscibot 038cf427b - Deploy kcjengr/qtpyvcp to github.com/kcjengr/qtpyvcp.git:gh-pages
[16:10:10] <Lcvette> TurBoss (@TurBoss:matrix.org): https://youtu.be
[16:10:22] <Lcvette> \o/
[16:12:24] <TurBoss> woah very nice
[16:12:40] <TurBoss> now you can take a carajillo !!!
[16:12:53] <TurBoss> hurray!!!
[16:13:15] <Lcvette> For real!
[16:13:17] <Lcvette> I need one
[16:13:36] <Lcvette> But for some reason on referencing the carousel it just keeps turning
[16:13:50] <Lcvette> Need to figure out why
[16:25:36] <Lcvette> TurBoss: do you remember we had that issue on the sim?
[16:25:48] <Lcvette> do you remember how we fixed?
[16:53:09] <Lcvette> TurBoss: the wheel just says referencing the whole time\
[16:53:34] <Lcvette> wonder if it needs a correct motion pin assigned so it knows when the carousel has received the input from the home sensor?
[16:58:51] <TurBoss> a missing m68
[17:00:34] <Lcvette> where?
[17:01:51] <Lcvette> i see an m68 in M14
[17:01:54] <Lcvette> ```
[17:02:06] * Lcvette sent a long message: < https://matrix.org >
[17:02:44] <Lcvette> no m68 in m13
[17:02:50] <TurBoss> hmmm
[17:03:00] <TurBoss> is there something in the atc_test
[17:03:00] * Lcvette sent a long message: < https://matrix.org >
[17:04:45] <TurBoss> I'm a bit away
[17:04:48] <TurBoss> be on latter
[17:04:50] <Lcvette> ok
[17:04:53] <TurBoss> * i'll be on latter
[17:05:05] <Lcvette> i'll leave it till then and work on the probe
[17:56:21] <jthornton> Ordered: 1 Shipped: 1 Backordered: 0 4852111 1/2in WOOD SLICER 111in
[18:24:58] <Lcvette> probing works awesome!!!!
[18:25:51] <Lcvette> soon as i can get the atc stuff sorted, i think everything will be working!\
[18:25:56] <Lcvette> \o/
[18:26:57] <Lcvette> jtthornton, you -not input was excellent and worked perfect on the probe!
[18:29:48] <jthornton> great
[18:30:58] <Lcvette> This is too cool
[18:40:33] <hazzy-m> yo
[18:40:52] <jthornton> yo-yo
[18:41:10] <Tom_L> Lcvette, was that part of the issue?
[18:41:23] <Lcvette> yo
[18:41:28] <Lcvette> o/
[18:41:35] <Lcvette> Tom_L: whats that?
[18:41:40] <Tom_L> -not
[18:41:49] <Lcvette> the -not?
[18:41:52] <Tom_L> or was that for something else
[18:42:15] <Lcvette> no, i just knew the probe needed an inverse because its connected all the time
[18:42:21] <Lcvette> and when it trips it opens
[18:42:27] <Tom_L> ahh
[18:42:39] <Lcvette> so i used the -not and it worked without complaint
[18:42:53] <Lcvette> so -not in 2.9 is the correct inverse
[18:42:54] <Tom_L> is that keyboard liquid proof?
[18:43:00] <Tom_L> kinda like it
[18:43:20] <Lcvette> which makes sense since the inverse on the halshow shows pin15-not
[18:43:32] <Lcvette> yes its completely sealed
[18:43:36] <Lcvette> and backlit
[18:43:41] <Tom_L> no it's because it's a daughter card instead of the main one
[18:43:53] <Lcvette> wasn't cheap but i knew i needed it water proof
[18:44:31] <Tom_L> the .in_not works on the main controler and -not works on daughter cards
[18:44:48] <Tom_L> just depends which one you're addressing
[18:45:16] <Tom_L> i see the atc works
[18:45:33] <Lcvette> almost works
[18:45:45] <Lcvette> need to resolve a bug when it tries to reference
[18:45:52] <Tom_L> does the spindle lift out of the way for a complete change?
[18:46:02] <Lcvette> some of the new code is interfering and it just turns and turn and turns
[18:46:03] <Lcvette> lol
[18:46:20] <Lcvette> yes
[18:46:41] <Tom_L> i don't see any vises or parts on that table!
[18:46:42] <Tom_L> wtf
[18:47:37] <Lcvette> https://youtu.be
[18:47:45] <Lcvette> its never cut a part yet
[18:48:05] <Lcvette> hoping it will this weekend
[19:05:11] <Not-5e4d> [02qtpyvcp] 07KurtJacobson published 03v0.2.5 | v0.2.5 - 13https://git.io/Je3Qo
[19:06:32] <jthornton> lol I have the same tool carousel on the BP discovery 308... you take a nap between tools
[19:06:48] <hazzy-m> lol
[19:22:51] <Tom_L> fadal are damn slow too
[19:29:13] * TurBoss is back
[19:29:58] <Lcvette> Yo
[19:30:03] <Lcvette> \o/
[19:30:10] <TurBoss> ok
[19:30:14] <TurBoss> sek i'll reboot
[19:30:19] <Lcvette> K
[19:30:31] <TurBoss> oho
[19:30:44] * TurBoss uploaded an image: image.png (26KB) < https://matrix.org >
[19:32:33] <Lcvette> What's that?
[19:39:47] <TurBoss> shutdown and update
[19:39:50] <TurBoss> I'm in
[19:40:25] <TurBoss> the referencing message never goes away?
[19:41:51] <Lcvette> no, it never references
[19:41:58] <Lcvette> it just keeps turning and turning and turning
[19:42:03] <TurBoss> oh lol
[19:42:05] <Lcvette> the m,achine
[19:42:09] <TurBoss> 😆
[19:42:16] <Lcvette> merrigoround
[19:42:18] <TurBoss> the machine is ok?
[19:42:28] <Lcvette> no machine is what keeps tuirning
[19:42:40] <TurBoss> oh
[19:42:41] <Lcvette> graphical wheel just sits saying referencing
[19:43:11] <TurBoss> so real atc never homes?
[19:43:42] <Lcvette> correct
[19:43:46] <Lcvette> just keeps turning
[19:44:10] <Lcvette> the original macros it homes corrrectly
[19:44:17] <TurBoss> can you send me m13.ngc?
[19:44:22] <Lcvette> so it has to be something newly added interfering i think mayb
[19:44:25] <TurBoss> both
[19:44:30] <TurBoss> ok cool
[19:46:15] * Lcvette posted a file: macros.tar.bz2 (3KB) < https://matrix.org >
[19:46:33] <Lcvette> these are the newly edited macros
[19:47:38] * Lcvette posted a file: macros_old.tar.bz2 (3KB) < https://matrix.org >
[19:47:47] <Lcvette> these are the old macros that worked
[19:49:27] <TurBoss> hmm
[19:52:54] <Lcvette> whatcha think
[19:53:23] <TurBoss> not much... making me a coffe
[19:53:24] <TurBoss> lol
[19:54:36] <Lcvette> ah
[19:54:40] <Lcvette> carillo
[19:54:47] <TurBoss> xD
[19:57:39] <TurBoss> is motion pin 3 wired in hal ?
[19:58:21] <TurBoss> it should is moving the atc...
[19:58:25] <TurBoss> :|
[19:58:39] <Lcvette> whats nmotion pin 3?
[20:00:05] * Lcvette sent a long message: < https://matrix.org >
[20:00:51] * Lcvette sent a long message: < https://matrix.org >
[20:00:56] <TurBoss> that
[20:01:17] <TurBoss> ```
[20:01:18] <TurBoss> net atc-fwd hm2_7i92.0.7i76.0.3.output-05 <= motion.digital-out-03
[20:01:24] <TurBoss> seems ok
[20:01:26] <TurBoss> ok
[20:01:34] <Lcvette> thats to turn it
[20:01:50] <TurBoss> yup
[20:01:53] <TurBoss> ok
[20:02:06] <Lcvette> ```net atc-is-out hm2_7i92.0.7i76.0.3.input-00 <= motion.digital-in-01
[20:02:07] <Lcvette> net atc-zero hm2_7i92.0.7i76.0.3.input-03 <= motion.digital-in-03
[20:02:14] <Lcvette> thats to stop it at home position
[20:02:58] <TurBoss> the same pin?
[20:03:03] <TurBoss> hmmm ok
[20:03:43] <Lcvette> one i smotion digital out the other is in
[20:04:20] <TurBoss> did work before?
[20:04:25] <Lcvette> yes
[20:10:00] <Lcvette> if i put the old m13 file in the new macros folder it homews correctly
[20:10:01] * TurBoss uploaded an image: image.png (117KB) < https://matrix.org >
[20:10:25] <TurBoss> ok
[20:11:02] <Lcvette> so it is something to do with the additional codes that were added
[20:11:14] <Lcvette> maybe they need to be inside of a routine?
[20:11:24] <TurBoss> hmmmm no idea
[20:11:44] <TurBoss> they are ins sub m13
[20:11:48] <Lcvette> what do the new codes do?
[20:12:15] <TurBoss> ```
[20:12:16] <TurBoss> M65 P10 (set atc widget unhomed)
[20:12:17] <TurBoss> M64 P11 (show atc widget referencing msg)
[20:12:30] <Lcvette> maybe: if 0130 etc
[20:12:33] * TurBoss sent a long message: < https://matrix.org >
[20:13:32] * TurBoss sent a long message: < https://matrix.org >
[20:13:45] <Lcvette> yes
[20:14:05] <Lcvette> that one works perfect
[20:14:16] <TurBoss> what is m14?
[20:14:26] <Lcvette> no clue
[20:14:27] <Lcvette> you made it
[20:14:36] <Lcvette> lol
[20:14:55] <TurBoss> ah
[20:14:57] <TurBoss> found it
[20:15:51] <TurBoss> what?
[20:15:58] <TurBoss> i dind't found it
[20:15:59] <TurBoss> :P
[20:16:06] <TurBoss> m14
[20:16:10] <TurBoss> is unknown?
[20:16:18] <Lcvette> the old macro has no m14
[20:16:33] <Lcvette> you made M14
[20:16:51] <TurBoss> m14 paints tools in the carousel
[20:17:04] <Lcvette> the original macros there isn't an M14 file
[20:17:09] <Lcvette> ah
[20:17:45] * TurBoss sent a long message: < https://matrix.org >
[20:17:58] <TurBoss> do you have it in place?
[20:18:14] <Lcvette> yes
[20:18:17] <TurBoss> cool
[20:18:20] <TurBoss> i just added a note
[20:18:25] <TurBoss> the comment
[20:19:00] <Lcvette> maybe the M13 needs some more structure?
[20:19:42] <TurBoss> can we see the value of #5399=
[20:19:44] <TurBoss> * can we see the value of #5399?
[20:19:58] <Lcvette> var table?
[20:20:01] <TurBoss> maybe it never changes
[20:20:03] <TurBoss> yes
[20:20:19] <TurBoss> but if with the old file works...
[20:20:25] <Lcvette> 5390 is as high as my var table goes
[20:20:34] <Lcvette> maybe it needs to be added?
[20:20:47] * TurBoss sent a long message: < https://matrix.org >
[20:21:00] <TurBoss> duno...
[20:21:29] <Lcvette> 5399 - Result of M66 - Check or wait for input. Volatile.
[20:22:15] <TurBoss> ok this section only checks if m66 is ok
[20:23:10] <TurBoss> is -1 or something abort
[20:23:21] <TurBoss> with lower than LT 0
[20:23:42] <Lcvette> dunno
[20:23:42] <Lcvette> i think so
[20:24:07] <TurBoss> how does the electronic sensor behabe?
[20:24:10] <TurBoss> with b or v
[20:24:15] <Lcvette> ?
[20:24:22] <Lcvette> has an index and a home
[20:24:38] <TurBoss> can you draw a timming diagram?
[20:24:42] <TurBoss> :P
[20:24:46] <Lcvette> ?
[20:25:04] <TurBoss> sek
[20:27:19] * TurBoss uploaded an image: timming.png (9KB) < https://matrix.org >
[20:27:30] <TurBoss> like this?
[20:27:41] <TurBoss> but 12 index
[20:28:11] <Lcvette> pocket 1 is where the home switch changes
[20:28:41] <TurBoss> so it turns until pocke 1 is reached?
[20:28:50] <Lcvette> yes
[20:28:56] <Lcvette> that the home position
[20:35:08] <TurBoss> Lcvette: you just changed the m13.ngc file to get it work?
[20:35:20] <Lcvette> yes
[20:35:35] <Lcvette> by reverting to the old m13 file it references the carousel
[20:35:57] <Lcvette> but the graphical dispolay doesn't work anymore
[20:36:02] <TurBoss> ok
[20:36:10] <Lcvette> i mean the un referenced sign
[20:36:24] <Lcvette> it still turns when you go atc fowd or rev
[20:37:02] <TurBoss> so its only show and hide the referencing messages..
[20:37:18] <TurBoss> can we just add some sections?
[20:37:30] <TurBoss> leave m14 for latter
[20:37:37] <Lcvette> I guess
[20:37:58] <TurBoss> so this goes before the m64 p3
[20:38:01] <TurBoss> ```
[20:38:02] <TurBoss> M65 P10 (set atc widget unhomed)
[20:38:03] <TurBoss> M64 P11 (show atc widget referencing msg)
[20:38:23] * TurBoss sent a long message: < https://matrix.org >
[20:38:34] <Lcvette> Can we just hashtag out parts?
[20:39:23] <TurBoss> #?
[20:39:30] <Lcvette> Yes
[20:39:37] <Lcvette> #m14
[20:39:42] <TurBoss> ;m14
[20:39:49] <Lcvette> Ok
[20:39:54] <TurBoss> or ()
[20:42:52] <Lcvette> works
[20:42:56] <TurBoss> hurray!
[20:42:58] <Lcvette> \o/
[20:43:02] <Lcvette> hurray!
[20:43:08] <TurBoss> ok the bug is less far
[20:43:19] <Lcvette> feature now?
[20:43:21] <Lcvette> lol
[20:43:25] <TurBoss> xD
[20:43:33] <TurBoss> how does your m14.ngc look?
[20:45:34] * Lcvette sent a long message: < https://matrix.org >
[20:46:25] <TurBoss> 😕
[20:49:08] <Lcvette> do you know what 5170 and 5171 are?
[20:49:28] <TurBoss> no
[20:50:23] <TurBoss> I'm still suspect from motion pin 3...
[20:50:40] <TurBoss> but not sure
[20:50:42] <TurBoss> :d
[20:50:43] <TurBoss> should be ok
[20:50:55] * Lcvette sent a long message: < https://matrix.org >
[20:50:57] <Lcvette> this worked
[20:51:13] <TurBoss> whoa!
[20:51:27] <Lcvette> i don't know why i thought to do it
[20:51:34] <Lcvette> but it worked
[20:52:01] <Lcvette> i don't have any tools in let me try adding tools to see if it paints them
[20:52:47] <TurBoss> maybe it doesn't draw the tools once homed....
[20:54:06] * TurBoss goes aft 10 min
[20:58:18] <Lcvette> nope doesnt draw the tools
[21:06:24] <TurBoss> back
[21:06:52] <Lcvette> i just realized i did not have the tool slots in the var table
[21:06:55] <Lcvette> jkust added them
[21:07:11] <Lcvette> going to try the code i sent easrlier again
[21:07:35] <TurBoss> ahh oh
[21:10:42] <Lcvette> didn't draw the tools
[21:10:47] <Lcvette> but they are in the var file now
[21:10:52] <TurBoss> ok
[21:10:57] <TurBoss> so
[21:11:02] <TurBoss> let me check on thing
[21:11:09] <Lcvette> k
[21:11:37] <TurBoss> do you have the m14 commented out?
[21:11:40] <TurBoss> with the ,
[21:11:42] <TurBoss> * with the ;
[21:11:44] <Lcvette> no
[21:11:52] <TurBoss> is in place?
[21:11:54] * Lcvette sent a long message: < https://matrix.org >
[21:11:59] <TurBoss> ah
[21:12:01] <TurBoss> ok
[21:12:13] <TurBoss> can we try without o130?
[21:12:18] <Lcvette> if i put it at the bottom just before the endsub it works
[21:13:05] * Lcvette sent a long message: < https://matrix.org >
[21:13:14] <TurBoss> ya that way
[21:13:25] <TurBoss> did you tried that?
[21:13:31] <TurBoss> * have you tried that?
[21:13:55] <Lcvette> yes, it homes but doesnt paint the tools
[21:14:18] <Lcvette> just tried it
[21:14:37] <TurBoss> what is the tool range?
[21:14:45] <TurBoss> 5190 +12?
[21:14:53] <Lcvette> 5190-5102
[21:15:00] <Lcvette> yes
[21:15:33] <TurBoss> are tools in the var file?
[21:15:59] * Lcvette sent a long message: < https://matrix.org >
[21:16:28] <Lcvette> i only put 4 tools in
[21:17:12] <Lcvette> tough bug
[21:17:28] <TurBoss> 😕
[21:17:40] <Lcvette> while i install the tools it paints them perfe4ctly
[21:17:59] <TurBoss> its only while homed true?
[21:18:12] <Lcvette> ?
[21:18:21] <Lcvette> its homes when im installing the tools
[21:18:24] <Lcvette> homed
[21:18:30] <Lcvette> the carousel
[21:18:42] <Lcvette> it paints them as i install them
[21:18:58] <Lcvette> but it does not paint them after booting up and referencing the carousel
[21:19:07] <Lcvette> all pockets are blank regardless ofwhats in the var file
[21:19:31] <TurBoss> ya because the m14 bug
[21:19:33] <TurBoss> cool
[21:19:35] <TurBoss> ok
[21:20:11] <TurBoss> found it
[21:20:13] <TurBoss> i think
[21:20:16] <Lcvette> should we run m14 before it starts to move?
[21:20:30] <TurBoss> when it finishes
[21:20:36] <Lcvette> or can it populate the var table on startup?
[21:20:56] <TurBoss> m14 will read the var table and paint pockets
[21:21:03] <TurBoss> if you call from mdi
[21:21:05] <TurBoss> or not
[21:21:12] <Lcvette> so can we use halui
[21:21:19] <Lcvette> mdi command at startup
[21:21:21] <TurBoss> ??
[21:21:22] <Lcvette> with M14?
[21:21:32] <TurBoss> its done on m13
[21:21:44] <Lcvette> but iot messes up m13
[21:22:15] <TurBoss> can you issue m14 ?
[21:22:20] <TurBoss> and see what happens
[21:22:34] <TurBoss> just after boot and home not referenced
[21:22:44] <TurBoss> carousel home
[21:22:53] <Lcvette> just tried
[21:22:55] <Lcvette> no paint
[21:22:57] <TurBoss> ok
[21:23:02] <TurBoss> so halui will no paint
[21:23:06] <Lcvette> so m14 is not working then
[21:23:21] <Lcvette> thats why it never finishes homing maybe?
[21:23:31] <TurBoss> i think...
[21:23:36] <TurBoss> seems related
[21:23:45] <TurBoss> its very close and its giving errors
[21:24:44] <TurBoss> maybe o101 exist
[21:24:49] <TurBoss> duno...
[21:25:43] <Lcvette> what o101?
[21:26:41] <TurBoss> I'm trying with sim
[21:27:35] <Lcvette> k
[21:27:35] <TurBoss> sim just worked
[21:28:29] <TurBoss> I homed the machine and issued m14
[21:28:38] <TurBoss> all tools ploped
[21:28:49] <Lcvette> maybe im missing something in qmol?
[21:28:55] <Lcvette> that you have and i don't?
[21:29:15] <TurBoss> the atc_motion.hal
[21:29:17] <Lcvette> i just tried changing to o999
[21:29:31] <Lcvette> i have the atc_motion.hal
[21:29:32] <TurBoss> same?
[21:29:34] <TurBoss> ok
[21:29:37] <Lcvette> dunno
[21:29:38] <Lcvette> sek
[21:29:53] * Lcvette sent a long message: < https://matrix.org >
[21:30:05] <TurBoss> do you have the atc_motion in your ini postGui_hal etc..?
[21:30:40] <TurBoss> I'll check how does the store tool paints
[21:30:51] <Lcvette> sec
[21:31:19] * Lcvette sent a long message: < https://matrix.org >
[21:31:48] <TurBoss> it should be ok because it draws when storing right?¿
[21:31:55] <Lcvette> yes
[21:32:00] <Lcvette> but not when rebooted
[21:32:25] <TurBoss> and you issuing m14 does nothing
[21:32:39] <TurBoss> ok
[21:33:59] <Lcvette> correct
[21:34:08] <Lcvette> issuing M14 before referencing carouself does nothing
[21:35:52] * TurBoss sent a long message: < https://matrix.org >
[21:35:56] * TurBoss sent a long message: < https://matrix.org >
[21:36:34] <TurBoss> this is the sim working config
[21:36:36] <TurBoss> :(
[21:36:46] <TurBoss> * this is the sim working sub
[21:37:05] <Lcvette> its same?
[21:37:14] <TurBoss> should be
[21:37:36] <TurBoss> ```
[21:37:37] <TurBoss> M68 E[#1 + 10] Q[#[5189 + #1]]
[21:37:38] <TurBoss> ```
[21:37:42] <TurBoss> here is the mess
[21:38:11] <TurBoss> #1 value is 1
[21:38:20] <Lcvette> you found it?
[21:38:22] <TurBoss> no
[21:41:10] * TurBoss sent a long message: < https://matrix.org >
[21:41:13] <Lcvette> there was one minor change between them i fixed but no worky still
[21:41:48] <TurBoss> so we can see since what number counts
[21:42:28] <Lcvette> run from terminal?
[21:42:33] <Lcvette> how to do again?
[21:42:33] <TurBoss> yes pleas
[21:43:04] <TurBoss> open a terminal and hit the up key since you find the correct command
[21:43:09] <TurBoss> up down
[21:43:26] <TurBoss> linuxcnc path to your ini
[21:44:15] <Lcvette> unknown mcode
[21:44:16] <Lcvette> m14
[21:44:25] <TurBoss> ok
[21:44:28] <TurBoss> we have something
[21:44:33] * Lcvette sent a long message: < https://matrix.org >
[21:44:34] <TurBoss> ini file
[21:44:55] <Lcvette> remap section!!!
[21:44:56] <Lcvette> hgahahahaha
[21:45:07] <TurBoss> yeah!
[21:46:22] <TurBoss> ok I'll work on notifications
[21:46:22] <Lcvette> just changed ini
[21:46:23] <Lcvette> testing
[21:46:34] <TurBoss> we would noticed
[21:47:07] <Lcvette> \o/
[21:47:11] <Lcvette> victorious
[21:47:18] <TurBoss> YEAH!
[21:47:26] <TurBoss> barvo!
[21:47:28] <Lcvette> it homes and works and paints now!!!!!
[21:47:28] <TurBoss> ole!
[21:47:34] <Lcvette> damn remap line in ini
[21:47:40] <TurBoss> hahahaha
[21:47:41] <Lcvette> ole ole ole ole!
[21:47:56] <TurBoss> damn missing notifications
[21:48:11] <Lcvette> we needs the notifications!
[21:48:26] <TurBoss> there exist a widget
[21:48:28] <TurBoss> a table
[21:48:34] <TurBoss> but requieres space
[21:48:37] <TurBoss> on UI
[21:48:45] <Lcvette> ?
[21:48:50] <Lcvette> box?
[21:49:03] <TurBoss> yes a box that shows notifications
[21:49:15] <TurBoss> not a popup
[21:49:18] <TurBoss> a history
[21:49:25] <Lcvette> can add a box on a back page and mauybe a led notification if there is an error?
[21:49:29] <Lcvette> is that possible maybe?
[21:49:31] <TurBoss> yes
[21:49:34] <TurBoss> sek I'll try
[21:49:43] <Lcvette> hurray!
[21:49:50] <Lcvette> lcvette goes to get a cigar
[21:49:59] <Lcvette> im on phone
[21:51:38] <TurBoss> wow
[21:51:47] <TurBoss> great day!
[21:51:49] <TurBoss> hahaha
[21:52:02] <TurBoss> I'm exicted!
[21:52:08] <TurBoss> 🙂
[21:52:11] <Lcvette> Phenomenal day
[21:52:51] <Lcvette> Pendant got resolved, probing was tested and works, ATC works, bearing cars fixed
[21:53:22] <Lcvette> If we get notifications working I think we are really close
[21:53:54] * TurBoss uploaded an image: image.png (79KB) < https://matrix.org >
[21:54:14] <TurBoss> \O/
[21:54:18] <TurBoss> * \o/
[21:54:22] <Lcvette> WHAT£=€=€°€°¢=¢
[21:54:31] <Lcvette> You did it already?
[21:54:36] <TurBoss> I just click spam
[21:54:42] <TurBoss> the box
[21:54:43] <TurBoss> yea
[21:55:41] <Lcvette> That's fantastic
[21:56:17] <TurBoss> but the popup is a must
[21:56:19] <TurBoss> no?
[21:56:35] <Lcvette> i can add an led somewhere on the fixed lower page
[21:56:58] <Lcvette> heading inside to dev ccomp-uter
[21:57:05] <Lcvette> back in a sek
[21:57:08] <TurBoss> ok
[21:58:44] <Lcvette> booting dev
[21:59:24] <Lcvette> did you push that?
[21:59:28] <TurBoss> no
[21:59:46] <TurBoss> I just draged the widget
[21:59:54] <TurBoss> from the designer
[22:00:15] <TurBoss> NotificationWidget in the widget list
[22:00:32] <TurBoss> it has buttons with filters
[22:00:51] * Lcvette sent a long message: < https://matrix.org >
[22:01:00] <Lcvette> error loading
[22:01:21] * Lcvette sent a long message: < https://matrix.org >
[22:01:23] <TurBoss> pip install pyqtgraph
[22:01:33] <TurBoss> or apt install python-pyqtgraph
[22:01:43] <TurBoss> doesn't matter
[22:04:58] <Lcvette> ok have the notifications widget on the status page
[22:05:03] <TurBoss> okay
[22:05:08] <Lcvette> o/ hazzy
[22:05:27] <TurBoss> oik
[22:05:35] <TurBoss> create a branch and push
[22:05:43] <TurBoss> I'll check and merge on master
[22:05:57] <Lcvette> im looking where to add the LED
[22:06:09] <TurBoss> how would the led work?
[22:06:35] <Lcvette> dunno
[22:06:37] <TurBoss> lol
[22:06:40] <Lcvette> thought you said it would work?
[22:06:42] <Lcvette> lol
[22:06:47] <TurBoss> I can add a signal
[22:06:52] <Lcvette> ok
[22:06:53] <TurBoss> ok give me a sek
[22:12:15] <Lcvette> 40
[22:12:53] <TurBoss> ?
[22:12:55] <TurBoss> :)
[22:13:30] <Lcvette> dual pc's
[22:13:37] <Lcvette> roamed to the wrong side
[22:13:38] <Lcvette> lol
[22:13:46] <TurBoss> hehe
[22:21:17] <TurBoss> @hazzy do you rememeber how we do widget signals?
[22:21:35] <TurBoss> can't remember lol
[22:22:26] <hazzy-m> hey!
[22:22:32] <TurBoss> Hi!
[22:22:33] <hazzy-m> I think so lkol
[22:22:35] <Lcvette> o/
[22:22:41] <hazzy-m> what are you trying to do?
[22:23:00] <TurBoss> send a signal to a led from the notification widget
[22:23:00] * hazzy-m reads the log
[22:23:16] <TurBoss> wow we did a log talk :D
[22:23:27] <TurBoss> * wow we did a long talk :D
[22:24:18] <Lcvette> to abutton
[22:24:21] <hazzy-m> what fires the LED?
[22:24:21] <Lcvette> :D
[22:24:32] <TurBoss> new notification message arrived
[22:24:32] <Lcvette> that way it can say nbotification inside it
[22:24:43] <hazzy-m> ah ok
[22:25:27] <TurBoss> and a reset button?
[22:25:42] <TurBoss> to reset the led?
[22:25:46] <Lcvette> reset buttopn?
[22:25:49] <hazzy-m> yeah, how would it be reset?
[22:25:58] <Lcvette> i'll just make it a button
[22:26:16] <TurBoss> use a ledbutton xD
[22:26:33] <hazzy-m> Lcvette: have you started laying it out?
[22:26:34] * Lcvette uploaded an image: Screenshot_2019-09-20_22-26-13.png (20KB) < https://matrix.org >
[22:26:40] <TurBoss> nice!
[22:26:47] <hazzy-m> nice!
[22:27:17] <Lcvette> I would like to make it so its transparent until active
[22:27:18] <TurBoss> hazzy: Lcvette just moved the atc stuff
[22:27:18] <hazzy-m> how about making the border of the notification button flash red?
[22:27:18] <Lcvette> then comes up Yellow
[22:27:19] <Lcvette> background
[22:27:19] <Lcvette> as a warning
[22:27:30] <hazzy-m> or that
[22:27:35] <Lcvette> been a while since i did anything in this im finding i have forgotten alot of it already
[22:27:43] <Lcvette> ok
[22:27:47] <Lcvette> dunno how
[22:27:54] <Lcvette> can you assist hazzy?
[22:28:10] <Lcvette> pushing
[22:28:16] <TurBoss> ok
[22:28:22] <TurBoss> I'll add the signal
[22:28:34] <TurBoss> if hazzy remembers how lul
[22:28:57] <Lcvette> pushed
[22:29:19] <TurBoss> ok
[22:29:33] <TurBoss> I'll figure
[22:29:46] <Lcvette> hazzy
[22:30:08] <Lcvette> r u avaiulable to tinkler?
[22:30:10] <Lcvette> tinker
[22:30:37] <hazzy-m> what we need is a new norification signal from the norification widget, and a way to reset it
[22:30:54] <Lcvette> that sounds good!
[22:31:01] <hazzy-m> r is on the wrong place on this keyboard lol
[22:32:31] <TurBoss> slot is fine
[22:32:39] <TurBoss> I saw some of them
[22:32:45] <Lcvette> r may be in the wrong place
[22:33:07] <TurBoss> in the wron place may be
[22:33:18] <TurBoss> haiku!
[22:33:40] <hazzy-m> haha
[22:33:42] <hazzy-m> miss that bot
[22:33:54] <TurBoss> he is having a nap
[22:34:18] <hazzy-m> Lcvette: what does clicking on the Notification buttin do? pop up a dialog?
[22:34:31] <TurBoss> reset?
[22:34:39] <Lcvette> no its just a signal to tell you to check the status page
[22:34:47] <Lcvette> where i put a big notification widget
[22:34:59] <Lcvette> otherwise you wouldn't know there was a notification to check
[22:34:59] <hazzy-m> ok
[22:35:14] <Lcvette> maybe could make it so it resets when pressed
[22:35:21] <TurBoss> yes
[22:35:25] <TurBoss> thats fine
[22:35:55] <Lcvette> maybe have it reset and take you to the status page?
[22:36:05] <TurBoss> ok
[22:36:05] <Lcvette> that would be cool
[22:36:07] <TurBoss> sound ok
[22:36:12] <hazzy-m> I like that
[22:36:17] <hazzy-m> should be easy enough
[22:36:24] <Lcvette> sweet!
[22:36:31] <hazzy-m> best to do that in probe_basic.py
[22:36:31] <Lcvette> ps did you see we got everything else working
[22:36:39] <hazzy-m> I'll have a go
[22:36:41] <hazzy-m> no
[22:36:47] <hazzy-m> HURRAY!!!
[22:37:03] <Lcvette> the notifications came when we wrestled with something that we found was a simple fix but no notifications hid the resolution from us
[22:37:04] <Lcvette> lol
[22:37:12] <Lcvette> probing works
[22:37:13] <TurBoss> lol
[22:37:15] <Lcvette> ATC all works
[22:37:18] <Lcvette> pendant works
[22:37:25] <Lcvette> bearing cars are replaced
[22:37:28] <hazzy-m> fandabulous!
[22:37:30] <Lcvette> was a productive day
[22:37:34] <TurBoss> \o//
[22:37:43] <Lcvette> \o/
[22:37:47] <TurBoss> ~o~
[22:37:50] <hazzy-m> what happend to the brearing cars?
[22:38:07] <Lcvette> they were the old clicking ones from the crash
[22:38:18] <Lcvette> i left them on until i got everything sorted with the pendant
[22:38:22] <Lcvette> just in case
[22:38:22] <Lcvette> lol
[22:38:31] <TurBoss> hurray!
[22:38:35] <Lcvette> hurray!
[22:38:36] <hazzy-m> good idea
[22:38:41] <Lcvette> \O/
[22:39:05] * TurBoss is unable to find how to emit stuff
[22:39:10] <TurBoss> can't remember :(
[22:39:53] <TurBoss> hazzy: do you have a new lappy?
[22:39:59] <TurBoss> hurray!
[22:40:13] <TurBoss> just remembered lol
[22:40:39] <hazzy-m> TurBoss: yes, I got a Lenovo X1 carbon, but I haven't but linux on it yet
[22:40:50] <TurBoss> hmmm
[22:41:00] <TurBoss> nice..
[22:41:13] <hazzy-m> still using a brick I got from a dumpster lol
[22:42:10] * hazzy-m uploaded an image: ima_3e15709.jpeg (182KB) < https://matrix.org >
[22:42:25] <TurBoss> wow
[22:42:30] <TurBoss> just readin screen specs
[22:42:34] <TurBoss> are high lol
[22:42:46] <TurBoss> for a 14"
[22:42:54] <hazzy-m> yeah, almost too high
[22:42:59] <hazzy-m> some apps don't work lol
[22:43:10] <TurBoss> lol=
[22:43:43] <TurBoss> Student of the year!
[22:43:46] <TurBoss> hurray!
[22:43:48] <Lcvette> CAUSE THE APPS ARE FROM THE SAME ERA AS THE DUMPSTER BRICK
[22:43:48] <TurBoss> xD
[22:43:48] <Lcvette> LOL
[22:43:57] <Lcvette> whoops caps
[22:49:52] * TurBoss uploaded an image: image.png (46KB) < https://matrix.org >
[22:50:02] <TurBoss> nice buttons got the qss style
[22:50:04] <Lcvette> \o/
[22:50:12] <Lcvette> yes
[22:50:15] <Lcvette> :D
[22:50:28] <Lcvette> how do i change the All Notifications syle?
[22:50:37] <TurBoss> ah
[22:50:44] <TurBoss> you can't lol
[22:50:54] * Lcvette sent a long message: < https://matrix.org >
[22:50:54] <TurBoss> :)
[22:51:03] <Lcvette> :o
[22:51:12] <TurBoss> you close :D
[22:51:22] <TurBoss> * you are close :D
[22:51:25] <Lcvette> i dunno what to do
[22:51:30] <TurBoss> ehhehehe
[22:51:32] <Lcvette> need a cheat sheet
[22:51:34] <Lcvette> lol
[22:51:41] <Lcvette> turboss halp
[22:51:45] <Lcvette> lol
[22:52:02] <TurBoss> firts the button led
[22:52:04] <TurBoss> stuff
[22:52:11] <Lcvette> i need a giant examples sheet for python
[22:52:18] <TurBoss> ah
[22:52:20] <TurBoss> cool
[22:52:42] <TurBoss> https://www.py4e.com
[23:05:57] <Not-5e4d> [02qtpyvcp] 07KurtJacobson created branch 03NotificationButton - 13https://git.io/fhCou
[23:05:58] <Not-5e4d> [02qtpyvcp] 07KurtJacobson pushed 032 commits to 03NotificationButton [+0/-0/±3] 13https://git.io/Je3Nh
[23:05:59] <Not-5e4d> [02qtpyvcp] 07Lcvette 03ae62eba - add notification widget to status page and notification button to main
[23:06:01] <Not-5e4d> [02qtpyvcp] 07KurtJacobson 036f4d3d4 - WIP: try to change notification button border red on error
[23:06:22] <Lcvette> \o/
[23:06:28] <hazzy-m> I have to sleep, more in the morning
[23:06:39] <TurBoss> night
[23:06:46] <Lcvette> night
[23:06:51] <Lcvette> thanks Hazzy!
[23:08:00] -!- travis-ci has joined #hazzy
[23:08:01] <travis-ci> kcjengr/qtpyvcp#1082 (NotificationButton - 6f4d3d4 : Kurt Jacobson): The build passed.
[23:08:01] <travis-ci> Diff view : https://github.com^...6f4d3d40941e
[23:08:01] <travis-ci> Build details : https://travis-ci.org
[23:08:01] -!- travis-ci has parted #hazzy
[23:09:15] <Lcvette> TurBoss: whatchu doin
[23:09:33] <Lcvette> lol
[23:09:35] <TurBoss> just checking what he did
[23:09:48] <Lcvette> hidden work
[23:09:58] <TurBoss> me
[23:09:58] <TurBoss> no
[23:10:49] <TurBoss> def onReturnPressed(self):
[23:10:50] <TurBoss> LOG.debug("Action entry activated with text: %s", self.text())
[23:10:51] <TurBoss> oops
[23:11:06] <Lcvette> \o/
[23:11:18] * TurBoss uploaded an image: image.png (654KB) < https://matrix.org >
[23:11:42] <TurBoss> a friend of mine did it
[23:11:43] <TurBoss> tomorrow wil machine it
[23:11:55] <TurBoss> is a footprint for warhammer
[23:12:16] <Lcvette> footprint?
[23:12:19] <TurBoss> hmmm
[23:12:29] <Lcvette> terrain layout?
[23:12:39] * TurBoss uploaded an image: image.png (91KB) < https://matrix.org >
[23:13:06] <Lcvette> gotcha
[23:14:25] * TurBoss leaves the dev machine
[23:14:49] <Lcvette> k
[23:14:51] <Lcvette> night
[23:22:51] <TurBoss> night