#linuxcnc-devel | Logs for 2019-03-05
Back
[00:28:54] -!- ve7it has quit [Remote host closed the connection]
[01:49:59] -!- c-log has quit [Ping timeout: 255 seconds]
[01:52:42] -!- c-log has joined #linuxcnc-devel
[02:08:27] -!- c-log has quit [Ping timeout: 240 seconds]
[02:10:06] -!- c-log has joined #linuxcnc-devel
[04:16:33] -!- JT-Shop has quit [Remote host closed the connection]
[04:17:37] -!- JT-Shop has joined #linuxcnc-devel
[06:16:45] -!- selroc has joined #linuxcnc-devel
[06:19:47] -!- selroc has quit [Client Quit]
[07:26:47] -!- mal`` has quit [Quit: Leaving]
[07:31:41] -!- mal`` has joined #linuxcnc-devel
[11:24:29] -!- JT-Shop has quit [Read error: Connection reset by peer]
[11:24:29] -!- jthornton has quit [Read error: Connection reset by peer]
[11:25:13] -!- jthornton has joined #linuxcnc-devel
[11:25:33] -!- JT-Shop2 has quit [Read error: Connection reset by peer]
[11:25:47] -!- JT-Shop has joined #linuxcnc-devel
[11:26:01] -!- JT-Shop2 has joined #linuxcnc-devel
[12:47:05] -!- ve7it has joined #linuxcnc-devel
[14:11:41] -!- andypugh has joined #linuxcnc-devel
[14:29:06] -!- alex_joni has quit [Read error: Connection reset by peer]
[14:34:18] -!- alex_joni has joined #linuxcnc-devel
[14:34:18] -!- mode/#linuxcnc-devel [+v alex_joni] by ChanServ
[16:32:57] -!- Roguish has quit [Ping timeout: 245 seconds]
[16:35:30] -!- Roguish has joined #linuxcnc-devel
[18:58:54] -!- ve7it has quit [Remote host closed the connection]
[18:59:41] -!- ve7it has joined #linuxcnc-devel
[19:12:08] -!- c-log has quit [Ping timeout: 245 seconds]
[19:14:01] -!- c-log has joined #linuxcnc-devel
[19:23:48] -!- andypugh has quit [Quit: andypugh]
[22:58:00] <skunkworks> pcw_home: you mentioned the sp491 - do you need the tristate enable for a lump? or would the sp490 work?
[23:04:01] -!- JT-Shop has quit [Remote host closed the connection]
[23:05:01] -!- JT-Shop has joined #linuxcnc-devel
[23:07:52] <pcw_home> Tri-state is not needed
[23:08:23] <Tom_L> what's ZRN coating on an endmill?
[23:08:28] <Tom_L> woops wrong window..
[23:08:44] <pcw_home> Zirconium Nitride?
[23:08:54] <Tom_L> possibly
[23:09:28] <Tom_L> wonder how that compares to TiALN
[23:11:05] <Tom_L> not quite as hard
[23:12:06] <Tom_L> https://acscoating.com
[23:15:41] <pcw_home> Didn't know there were so many different hard coatings
[23:15:50] <Tom_L> me either
[23:16:10] <Tom_L> they seem to be getting more specific
[23:19:49] <skunkworks> thanks!
[23:45:18] * hazzy-m would expect ZRN to be harder then TiALN