#linuxcnc-devel | Logs for 2019-03-23
Back
[00:22:21] -!- ve7it has quit [Remote host closed the connection]
[01:22:36] -!- c-log has quit [Ping timeout: 272 seconds]
[01:24:22] -!- c-log has joined #linuxcnc-devel
[01:46:31] -!- c-log has quit [Ping timeout: 255 seconds]
[01:49:40] -!- c-log has joined #linuxcnc-devel
[02:49:07] <CMorley> mozmck: https://forum.linuxcnc.org
[03:40:25] <linuxcnc-build> build #4021 of 1403.rip-wheezy-amd64 is complete: Failure [4failed apt-get-update install-missing-build-dependencies configuring] Build details are at http://buildbot.linuxcnc.org blamelist: Chris Morley <chrisinnanaimo@hotmail.com>
[03:40:35] <linuxcnc-build> build #4020 of 1400.rip-wheezy-i386 is complete: Failure [4failed apt-get-update install-missing-build-dependencies configuring] Build details are at http://buildbot.linuxcnc.org blamelist: Chris Morley <chrisinnanaimo@hotmail.com>
[03:40:57] <linuxcnc-build> build #3013 of 1903.clang-wheezy-amd64 is complete: Failure [4failed apt-get-update install-missing-build-dependencies configuring] Build details are at http://buildbot.linuxcnc.org blamelist: Chris Morley <chrisinnanaimo@hotmail.com>
[03:41:26] <linuxcnc-build> build #3536 of 1402.rip-wheezy-rtpreempt-i386 is complete: Failure [4failed apt-get-update install-missing-build-dependencies configuring] Build details are at http://buildbot.linuxcnc.org blamelist: Chris Morley <chrisinnanaimo@hotmail.com>
[03:54:50] -!- c-log has quit [Ping timeout: 250 seconds]
[03:57:45] -!- c-log has joined #linuxcnc-devel
[04:15:56] <linuxcnc-build> build #5882 of 0000.checkin is complete: Failure [4failed] Build details are at http://buildbot.linuxcnc.org blamelist: Chris Morley <chrisinnanaimo@hotmail.com>
[10:40:02] -!- skunkworks has quit [Ping timeout: 245 seconds]
[12:30:27] -!- skunkworks has joined #linuxcnc-devel
[12:52:07] -!- ve7it has joined #linuxcnc-devel
[12:59:32] -!- c-log has quit [Ping timeout: 250 seconds]
[13:00:59] -!- c-log has joined #linuxcnc-devel
[13:01:05] -!- c-log has quit [Changing host]
[13:01:05] -!- c-log has joined #linuxcnc-devel
[14:11:24] -!- pcw_home has quit [Ping timeout: 252 seconds]
[15:08:44] -!- pcw_home has joined #linuxcnc-devel
[17:22:55] -!- andypugh has joined #linuxcnc-devel
[17:41:07] <Tom_L> noticed a little unusual behavior in 2.8 on wheezy
[17:41:57] <Tom_L> run from line just above the 3rd tool change it asked me for the first 2 tools before manual toolchange asked for the correct one
[17:42:20] <Tom_L> no motion, just requested the first 2 tools then the correct one
[17:44:41] <andypugh> I think this is part of an attempt to do run-from-line from the right state.
[17:45:21] <Tom_L> line was just a G20 Z0 just before the T1 M6
[17:45:27] <andypugh> But it does sound like a tweak might be in order
[17:45:52] <Tom_L> T1 being the 3rd tool in order this time
[21:04:05] <Tom_L> log
[21:04:05] <c-log> Tom_L: Today's Log http://tom-itx.no-ip.biz:81
[21:51:35] -!- Tom_shop has joined #linuxcnc-devel
[21:53:14] -!- Tom_shop has quit [Client Quit]
[22:22:26] -!- Tom_itx has joined #linuxcnc-devel
[22:31:01] -!- Tom_itx has quit [Quit: Leaving]
[22:48:38] -!- andypugh has quit [Quit: andypugh]
[23:38:48] -!- _njh_ has quit [Ping timeout: 245 seconds]
[23:40:19] -!- njh has joined #linuxcnc-devel
[23:58:23] -!- Tom_shop has joined #linuxcnc-devel
[23:58:48] -!- Tom_shop has quit [Client Quit]
[23:59:07] -!- Tom_shop has joined #linuxcnc-devel