#linuxcnc | Logs for 2019-03-30
Back
[09:03:07] -!- logs has joined #linuxcnc
[09:06:35] -!- Isleape has quit [Quit: Isleape]
[09:12:46] <jthornton> joint.somenumber.velocity
[09:14:26] -!- gloops has joined #linuxcnc
[09:14:31] <pink_vampire> i mean the general velocity
[09:16:59] <jthornton> motion.current-vel
[09:17:00] -!- sumpfralle has joined #linuxcnc
[09:17:30] <pink_vampire> it that a signal? or a pin?
[09:17:42] <pink_vampire> i'm trying to find it in the hal meter
[09:18:04] <jthornton> pin\
[09:18:13] <jthornton> open up Show Hal configuration\
[09:18:18] <pink_vampire> **hal configuration
[09:20:14] <pink_vampire> motion.current-vel give me mm/s
[09:20:44] <pink_vampire> is there a way to convert i in pyvcp to mm/min?
[09:28:48] <fdarling> pink_vampire: what do you mean by "i"? did you mean "it"?
[09:29:25] <pink_vampire> yes
[09:29:50] <fdarling> pink_vampire: when you say PyVCP, do you mean a custom panel you added to the side of AXIS?
[09:30:19] <fdarling> pink_vampire: I would imagine you could use a HAL component to scale the value up by 60 to go from units per second to minute
[09:30:27] -!- gloops has quit [Ping timeout: 255 seconds]
[09:33:39] <pink_vampire> yes, correct
[09:33:48] <fdarling> pink_vampire: do you need help with that?
[09:34:06] <pink_vampire> yes
[09:34:21] <pink_vampire> i have no idea how to do it
[09:41:00] <pink_vampire> this is line 74: net ipm-out pyvcp.feed-rate <= mult2.0.ou
[09:41:20] <pink_vampire> this is the error Debug file information: custom_postgui.hal:74: Signal 'ipm-out' of type 's32' cannot add pin 'mult2.0.out' of type 'float'
[09:44:36] <jthornton> data types must match, if not you must convert them
[09:45:19] <pink_vampire> i took it from here https://forum.linuxcnc.org
[09:45:29] <jthornton> http://linuxcnc.org
[09:46:46] <jthornton> wow that's from 2011, I'll see if it still works in master
[09:47:30] <pink_vampire> yeah.. i hope it will..
[09:51:54] <jthornton> yea it still works fine
[09:52:56] <jthornton> what pyvcp number display did you use? I'm guessing one that has s32 inputs
[09:53:27] <fdarling> pink_vampire: I just tested a way of doing it
[09:53:32] <pink_vampire> i want to use the bar type
[09:56:54] <fdarling> pink_vampire: https://pastebin.com
[09:57:47] <pink_vampire> lets see
[09:59:11] -!- JesusAlos has quit [Quit: JesusAlos]
[10:02:00] <pink_vampire> fdarling: THANKS!! work perfect!
[10:05:31] -!- ferdna has joined #linuxcnc
[10:07:19] * Tom_L puts the fire out under jthornton's box
[10:08:10] <Tom_L> jthornton, i wasn't trying to copy them but just install one from the menu
[10:08:32] <Tom_L> err well i guess it copies them to my local dir..
[10:10:57] <Tom_L> but either way, it won't create an icon or copy the files over
[10:11:55] <Tom_L> maybe someone should just add a 'chown' statement to the install help :)
[10:24:00] -!- gloops has joined #linuxcnc
[10:28:22] <jthornton> the config picker will force you to copy them when you run a sim the first time
[10:28:32] * jthornton will be back in a bit
[10:45:28] <Tom_L> kindof a catch 22 if they won't copy
[11:11:45] -!- joaj has joined #linuxcnc
[11:27:22] <Jymmm> Morning folks
[11:30:19] <Deejay> good afternoon
[11:32:35] <gregcnc> wow, found not one, but two chucks for my lathe on ebay this morning
[11:35:12] -!- net| has joined #linuxcnc
[11:39:33] <gloops> funny how stuff comes in batches like that, you see several of one thing in one week, then none of those same things again for months
[11:39:48] <gloops> usually when i want one
[11:40:29] <gregcnc> these are very unusual. I found one last year at three times the price
[11:43:00] <gloops> ive got an american taper chuck going rusty i ought to put it on ebay really, someone could be using it
[11:46:36] -!- FinboySlick has joined #linuxcnc
[11:46:53] -!- FinboySlick has quit [Client Quit]
[11:49:00] -!- swarfer has joined #linuxcnc
[11:50:31] -!- swarfer has quit [Client Quit]
[11:53:31] -!- joaj has quit [Remote host closed the connection]
[11:58:28] <jthornton> Tom_L: is this just a normal install?
[12:15:41] <jthornton> something ain't normal if sims won't copy
[12:26:03] <Tom_L> normal as they get
[12:26:28] <Tom_L> i don't remember if i used the iso or installed stretch and added preempt-rt
[12:26:54] <Tom_L> then upgraded to 2.8
[12:30:41] -!- mase-tech has joined #linuxcnc
[12:31:51] <jthornton> something ain't right for sure
[12:32:59] <jthornton> did it work before upgrading to master?
[12:37:07] <mase-tech> hi
[12:51:32] -!- swarfer has joined #linuxcnc
[12:51:46] -!- swarfer has quit [Client Quit]
[13:11:27] flyback is now known as phlyback
[13:22:08] -!- DaPeace has quit [Quit: Leaving.]
[13:22:26] -!- DaPeace has joined #linuxcnc
[13:22:55] phlyback is now known as flyback
[13:29:30] -!- zoukils has joined #linuxcnc
[13:31:11] -!- zoukils has quit [Client Quit]
[14:09:18] -!- ve7it has joined #linuxcnc
[14:15:59] -!- DaPeace has quit [Quit: Leaving.]
[14:17:17] -!- JT-Shop has quit [Read error: Connection reset by peer]
[14:18:18] -!- jthornton has quit [Read error: Connection reset by peer]
[14:19:02] -!- JT-Shop has joined #linuxcnc
[14:19:51] -!- jthornton has joined #linuxcnc
[14:41:31] -!- JT-Shop has quit [Read error: Connection reset by peer]
[14:42:02] -!- JT-Shop has joined #linuxcnc
[14:58:05] -!- jthornton has quit [Read error: Connection timed out]
[14:58:43] -!- jthornton has joined #linuxcnc
[15:27:17] -!- swarfer has joined #linuxcnc
[15:29:13] -!- swarfer has quit [Client Quit]
[15:32:47] -!- swarfer has joined #linuxcnc
[15:33:27] -!- jthornton has quit [Read error: Connection reset by peer]
[15:33:48] -!- JT-Shop has quit [Read error: Connection reset by peer]
[15:33:54] -!- jthornton has joined #linuxcnc
[15:34:12] -!- JT-Shop has joined #linuxcnc
[15:35:52] -!- swarfer has quit [Client Quit]
[15:40:33] -!- leorat has joined #linuxcnc
[15:45:13] -!- c-log has quit [Ping timeout: 246 seconds]
[15:48:16] -!- c-log has joined #linuxcnc
[16:16:35] -!- lostinsip has joined #linuxcnc
[16:18:23] <skunkworks> http://electronicsam.com
[16:19:07] <skunkworks> http://electronicsam.com
[16:32:49] -!- JT-Shop has quit [Read error: Connection reset by peer]
[16:32:52] -!- jthornton has quit [Read error: Connection reset by peer]
[16:33:25] -!- JT-Shop has joined #linuxcnc
[16:33:25] -!- jthornton has joined #linuxcnc
[16:38:53] <net|> skunkworks you should downsize those images to 1200x800
[16:40:02] -!- lostinsip has quit [Quit: Leaving]
[16:40:18] <net|> some linuxcnc'rs probably still use dialup
[16:46:02] <XXCoder> yep more remote areas anyway
[16:53:34] -!- ferdna has quit [Quit: Leaving]
[16:55:13] <jthornton> https://youtu.be
[16:56:29] <XXCoder> thats quite complete help system
[16:56:37] <jthornton> thanks
[16:57:15] <jthornton> old farts can't remember crap so having the list of g codes at the mill is a huge help
[17:01:31] <XXCoder> ill reward you with weird video https://youtu.be
[17:01:34] <XXCoder> really funny
[17:06:19] -!- JT-Shop has quit [Read error: Connection reset by peer]
[17:06:22] -!- jthornton has quit [Read error: Connection reset by peer]
[17:06:47] -!- JT-Shop has joined #linuxcnc
[17:06:51] -!- jthornton has joined #linuxcnc
[17:31:24] <skunkworks> sorry - another big one..
[17:31:26] <skunkworks> http://electronicsam.com
[17:31:41] <skunkworks> looks like it will work as an index.. (the little hole)
[17:32:25] <XXCoder> whats with damage to one of holes
[17:32:48] -!- Samiam1999DTP has quit [Read error: Connection reset by peer]
[17:33:40] <skunkworks> should use a spanner - used a punch
[17:34:47] <XXCoder> doh
[17:37:55] -!- gloops has quit [Ping timeout: 246 seconds]
[17:57:17] -!- DrUbuntu has joined #linuxcnc
[18:00:17] -!- DrUbuntu has quit [Client Quit]
[18:01:48] -!- DrUbuntu has joined #linuxcnc
[18:02:23] -!- gesichtsfuss has joined #linuxcnc
[18:03:57] -!- gesichtsfuss has quit [Remote host closed the connection]
[18:03:57] -!- DrUbuntu has quit [Remote host closed the connection]
[18:53:34] -!- veek has joined #linuxcnc
[18:55:33] <Tom_L> skunkworks for the spindle motor you've been testing?
[18:55:44] <Tom_L> hope you trim the screws before you add a belt :)
[18:56:37] <Deejay> gn8
[18:57:29] -!- Deejay has quit [Quit: bye]
[18:58:18] <Tom_L> JT-Shop is your gui ready to test live yet?
[19:00:19] <jthornton> which one?
[19:01:09] <jthornton> https://github.com
[19:01:33] <Tom_L> the last video
[19:01:45] <Tom_L> MDI
[19:01:47] <jthornton> yea most of it is working
[19:02:18] <Tom_L> can you display the tool table and set work offsets etc?
[19:02:19] <jthornton> https://github.com
[19:02:33] <Tom_L> i don't have touch though
[19:02:39] <jthornton> you can set g5x and g92 offsets
[19:02:45] <jthornton> works with a mouse too
[19:02:46] <Tom_L> and i can't really run it live due to wheezy
[19:03:07] <Tom_L> and rtai
[19:03:18] <jthornton> you need debian 9 or linux mint 19 I think to even run it
[19:03:23] <Tom_L> yeah
[19:03:39] <Tom_L> i've got 9 on the test pc but i'm having issues with it aparently
[19:03:57] <jthornton> yea wtf is up with that?
[19:04:12] <Tom_L> maybe i'll get a chance to work on it this evening
[19:04:15] <Tom_L> i've no idea
[19:04:38] <jthornton> you might try using my install instructions for debian 9
[19:04:43] <Tom_L> i got one graphic one going but it won't copy them now
[19:04:53] <Tom_L> i think i may have trouble with it even
[19:05:03] <jthornton> https://youtu.be
[19:06:23] <Tom_L> the MDI stuff i wouldn't use so much
[19:13:19] <skunkworks> Tom_L: yes - the screws are a little long..
[19:21:34] <Tom_L> JT-Shop do you know where the sims are kept so i can chown the dir and try that?
[19:23:06] -!- ve7it has quit [Remote host closed the connection]
[19:23:48] -!- ve7it has joined #linuxcnc
[19:25:07] -!- veek has quit [Quit: Leaving]
[19:25:41] <jthornton> you could just clone and they are all there
[19:26:11] <jthornton> but if my system was that messed up I'd start over
[19:26:52] <Tom_L> funny thing is i was able to get gmocappy copied
[19:27:46] <Tom_L> it couldn't be that messed up being a fresh install with hardly anything done on it
[19:29:21] <jthornton> something is very wrong if you run the config picker and it can't copy the sim...
[19:30:54] <Tom_L> i suppose i could run the iso again but i've got everything set the way i want it now :(
[19:31:22] <jthornton> except it can't copy a sim...
[19:31:51] <Tom_L> oh.. i'm pretty sure i installed from debian because i didn't like the iso desktop
[19:32:09] <Tom_L> i wanted mate instead
[19:33:12] <jthornton> yea, I install mate desktop
[19:33:28] <jthornton> http://gnipsel.com
[19:38:11] -!- ferdna has joined #linuxcnc
[19:45:46] <Tom_L> chown fixed it
[19:49:55] -!- mase-tech has quit [Quit: Leaving]
[19:54:27] <Tom_L> i would think /usr/share wouldn't be owned by root
[20:12:44] <Tom_L> JT-Shop where was your page for installing QtPyVCP?
[20:13:07] <Tom_L> oops.. found it
[20:31:28] -!- infornography has joined #linuxcnc
[20:37:59] <jthornton> yea usr/share is owned by root
[20:38:48] <infornography> is it for sale?
[20:39:20] <Tom_L> but it should allow users to read it right?
[20:39:43] <Tom_L> the 'copy' to usr dir is probably where it hangs
[20:54:17] <pink_vampire> i have a problem,
[20:56:03] <Jymmm> pink_vampire: Plan C ???
[20:56:23] <pink_vampire> how can i get angular feed on a separate pypcp bar?
[20:57:09] <pink_vampire> the linear feeds are 0-2400 mm/min but the angular feed is 0-86040 deg/min
[20:58:06] <pink_vampire> the bar is set to 0-2400, so any motion in the rotation axis make it go to the maximum
[20:59:18] <pink_vampire> the bar is connected to this code: https://pastebin.com
[21:08:33] <Tom_L> show a separate rotational axis bar?
[21:08:48] <pink_vampire> yeah
[21:23:40] -!- asdfasd1 has quit [Ping timeout: 246 seconds]
[21:23:43] <Tom_L> well i muffed something else up.. i may as well start over
[21:24:19] <Tom_L> JT-Shop, stretch uspace amd 64 what i want?
[21:24:35] <Tom_L> (that's what i labelled the disk anyway)...
[21:25:39] <pink_vampire> not sure
[21:27:12] <pink_vampire> Tom_L: do you know what is that halpin name for velocity per axis?
[21:32:08] <Tom_L> no
[21:34:01] <pink_vampire> i think i found it
[21:34:04] <pink_vampire> axis.0.joint-vel-cmd
[21:50:40] -!- ziper has joined #linuxcnc
[22:11:51] -!- gloops has joined #linuxcnc
[22:12:02] <Tom_L> hey gloops
[22:29:08] -!- Tom_itx has joined #linuxcnc
[22:29:32] Tom_itx is now known as Guest74348
[22:29:59] -!- Guest74348 has quit [Client Quit]
[22:32:06] -!- Tom_itx has joined #linuxcnc
[22:32:29] Tom_itx is now known as Guest85174
[22:32:38] -!- Guest85174 has quit [Client Quit]
[22:32:54] -!- gloops has quit [Ping timeout: 250 seconds]
[22:45:42] -!- Tom_test has joined #linuxcnc
[22:51:53] <net|> https://drive.google.com fresh linux development image for virtualbox with qt and codeblocks preinstalled and a couple of ai libs.
[22:59:53] <net|> 4.1gb
[23:12:38] <net|> im hoping it went ok my router powercycled during upload
[23:13:05] <pink_vampire> make md5sum
[23:15:14] <net|> i sent feedback to google to ask for the option
[23:17:13] <pink_vampire> i mean - you need to make an md5sum locale on your computer, and this way we can compered it to the uploaded file, if the server will make md5sum to a broken file, it is not going to help us.
[23:19:46] <net|> a08ddf3b94dd8679482bb6877dcf09df Suse15leap.7z
[23:21:10] <pink_vampire> Suse15leap.7z (3.8G)
[23:21:31] <pink_vampire> your end show 4.1gb??
[23:26:39] <net|> yeah 3.8 is the max it will scan for viruses
[23:27:09] <net|> it uploaded ok it said, my internet is only 500kb/s usually so it'll be a while before i verify it
[23:27:59] <pink_vampire> here it is download on 6.3MB/s
[23:28:18] <Jymmm> net|: No no, you run md5sum on your computer, not on the uploaded file
[23:29:12] <net|> i did thats the number i gave
[23:29:26] <net|> pink_vampire impressive
[23:34:41] <net|> does that mean it takes 6 min to download 4100 mb ?
[23:37:44] <Jymmm> times 8
[23:38:21] <Jymmm> communictiations is in BITS, storage is in BYTES
[23:39:42] <pink_vampire> it id done!
[23:40:46] * net| eagerly awaits md5 verification
[23:42:14] <XXCoder> just remember that theres difference between theorical max speed of connection vs real world
[23:42:42] <Elmo40> ugh... more snow...
[23:42:46] <Elmo40> when will Winter end?
[23:43:58] <XXCoder> alrerady ended for me
[23:45:06] <pink_vampire> 5%...
[23:49:47] <Tom_L> anybody recall jt's link to the deb for master 2.8?
[23:51:37] <Tom_L> ahh found it..
[23:52:26] -!- Tom_test has quit [Quit: Leaving]
[23:54:10] <pink_vampire> net|: the md5 is correct
[23:54:27] <pink_vampire> it is unzip it now